Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and the front seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1905/74 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib LH circuit during the primary check.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1906/74 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1907/74 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1908/74 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E08
4.762,2.554 5.200,2.719 0.437,0.165 10 PL- 4.762,1.7 5.151,1.865 0.389,0.165 10 PL+ 2.164,2.435 2.341,2.600 0.177,0.165 10 L- 2.164,1.595 2.341,1.759 0.177,0.165 10 L+ 2.439,2.394 2.641,2.575 0.203,0.181 10 2 2.439,1.541 2.641,1.722 0.203,0.181 10 1 0.604,3.256 2.808,3.433 2.204,0.177 10 Front Pretensioner Squib LH 0.072,0.062 2.275,0.239 2.204,0.177 12 w/ Side Airbag: 0.604,3.093 0.945,3.231 0.341,0.138 10 K1 4.84,4.299 6.237,4.475 1.398,0.177 10 Center Airbag Sensor 4.84,4.177 5.180,4.315 0.341,0.138 10 K27 4.522,1.617 4.744,1.782 0.222,0.166 10 5 4.522,2.431 4.744,2.597 0.222,0.166 10 6

C178002E17
4.762,2.554 5.200,2.719 0.437,0.165 10 PL- 4.762,1.7 5.151,1.865 0.389,0.165 10 PL+ 2.164,2.435 2.341,2.600 0.177,0.165 10 L- 2.164,1.595 2.341,1.759 0.177,0.165 10 L+ 2.439,2.395 2.641,2.575 0.203,0.181 10 2 2.439,1.541 2.641,1.722 0.203,0.181 10 1 0.604,3.256 2.808,3.433 2.204,0.177 10 Front Pretensioner Squib LH 0.072,0.062 2.275,0.239 2.204,0.177 12 w/o Side Airbag: 0.604,3.093 0.945,3.231 0.341,0.138 10 K1 4.84,4.299 6.237,4.475 1.398,0.177 10 Center Airbag Sensor 4.84,4.177 5.180,4.315 0.341,0.138 10 K32 4.522,1.617 4.744,1.782 0.222,0.166 10 2 4.522,2.431 4.744,2.597 0.222,0.166 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
a.

Turn the ignition switch off.

U164756E01
0.132,0.025 1.316,0.268 1.184,0.244 12 w/ Side Airbag: 0.132,2.023 1.390,2.189 1.258,0.165 12 w/o Side Airbag: 1.608,2.902 1.727,3.049 0.118,0.147 10 C 1.432,2.902 1.550,3.049 0.118,0.147 10 D 1.716,3.195 3.113,3.348 1.398,0.152 10 Center Airbag Sensor 0.431,3.484 2.232,3.626 1.801,0.142 10 Front Pretensioner Squib LH 1.608,0.861 1.727,1.007 0.118,0.147 10 C 1.432,0.861 1.550,1.007 0.118,0.147 10 D 1.716,1.392 3.113,1.544 1.398,0.152 10 Center Airbag Sensor 0.314,1.164 1.498,1.542 1.184,0.378 10 Front Pretensioner Squib LH 1.287,0.783 0.908,0.996 0.908,0.996 0.908,1.136 false 1.321,2.828 1.321,3.484 false 3.685,0.55 6.045,0.926 2.360,0.376 10 Front view of wire harness connector: (to Front Pretensioner Squib LH) 4.018,1.664 4.290,1.849 0.272,0.184 10 K1 5.48,1.65 6.321,1.829 0.840,0.179 10 Connector C 5.793,2.211 6.112,2.355 0.320,0.144 10 SST 5.287,1.863 5.757,2.275 false


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt LH.


d.

Connect the yellow wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.

Disconnect the connectors from the center airbag sensor.

U164757E01
0.079,0.06 1.402,0.332 1.323,0.272 12 w/ Side Airbag: 0.079,1.835 1.402,2.106 1.323,0.272 12 w/o Side Airbag: 2.049,2.699 2.226,2.904 0.176,0.205 10 A 1.732,2.898 1.908,3.102 0.176,0.205 10 B 1.436,2.898 1.612,3.102 0.176,0.205 10 C 1.239,2.898 1.416,3.102 0.176,0.205 10 D 1.639,3.196 3.042,3.364 1.402,0.168 10 Center Airbag Sensor 0.148,3.117 1.360,3.432 1.213,0.315 10 Front Pretensioner Squib LH 1.109,2.822 0.739,3.014 0.739,3.014 0.739,3.114 false 0.865,2.331 1.548,2.492 0.683,0.161 10 Floor Wire 1.618,2.714 1.618,2.409 1.618,2.409 1.536,2.409 false 2.049,0.654 2.226,0.858 0.176,0.205 10 A 1.732,0.852 1.908,1.057 0.176,0.205 10 B 1.436,0.852 1.612,1.057 0.176,0.205 10 C 1.239,0.852 1.416,1.057 0.176,0.205 10 D 1.639,1.375 3.042,1.543 1.402,0.168 10 Center Airbag Sensor 0.148,1.072 1.360,1.387 1.213,0.315 10 Front Pretensioner Squib LH 1.109,0.776 0.739,0.968 0.739,0.968 0.739,1.069 false 1.729,0.285 2.412,0.446 0.683,0.161 10 Floor Wire 1.633,0.669 1.633,0.363 1.633,0.363 1.715,0.363 false 3.725,0.657 6.080,1.002 2.355,0.345 10 Front view of wire harness connector: (to Front Pretensioner Squib LH) 4.129,1.482 4.340,1.657 0.211,0.175 10 K1 5.38,1.537 6.229,1.694 0.849,0.157 10 Connector C 4.225,1.986 4.451,2.173 0.227,0.188 10 L+ 5.395,1.986 5.621,2.173 0.227,0.188 10 L- 4.935,1.599 5.374,2.024 false 4.83,1.599 4.391,2.024 false 1.744,0.662 1.783,0.623 false 1.744,0.715 1.83,0.628 false 1.744,0.767 1.83,0.681 false 1.744,0.82 1.83,0.734 false 1.789,0.827 1.83,0.787 false 1.742,2.705 1.781,2.666 false 1.742,2.758 1.828,2.671 false 1.742,2.811 1.828,2.724 false 1.742,2.864 1.828,2.777 false 1.788,2.871 1.828,2.83 false


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K1-1 (L+) - Body ground Ignition switch ON Below 1 V
K1-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-1 (L+) - K1-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-1 (L+) - K1-2 (L-) Always 1 MΩ or higher
K1-1 (L+) - Body ground Always 1 MΩ or higher
K1-2 (L-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C173651E01
0.066,0.059 1.287,0.326 1.221,0.267 12 w/ Side Airbag: 0.066,2.26 1.425,2.527 1.360,0.267 12 w/o Side Airbag: 1.166,3.719 1.294,3.867 0.127,0.148 10 C 1.044,3.719 1.172,3.867 0.127,0.148 10 D 1.269,4.092 2.667,4.238 1.398,0.146 10 Center Airbag Sensor 1.102,2.737 2.904,2.893 1.802,0.156 10 Front Pretensioner Squib LH 0.956,3.502 0.956,2.826 0.956,2.826 1.07,2.826 false 1.166,1.21 1.294,1.357 0.127,0.148 10 C 1.044,1.21 1.172,1.357 0.127,0.148 10 D 1.269,1.851 2.667,1.997 1.398,0.146 10 Center Airbag Sensor 1.102,0.52 2.904,0.676 1.802,0.156 10 Front Pretensioner Squib LH 0.956,0.992 0.956,0.609 0.956,0.609 1.07,0.609 false

Connect the connectors to the front seat outer belt LH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.




OK

NG