Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1830/57  Short in Curtain Shield Squib RH Circuit  B1831/57  Open in Curtain Shield Squib RH Circuit  B1832/57  Short to GND in Curtain Shield Squib RH Circuit  B1833/57  Short to B+ in Curtain Shield Squib RH Circuit  


DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor and the curtain shield airbag RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1830/57 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1831/57 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the curtain shield squib RH circuit for 2 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1832/57 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1833/57 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E02
1.928,1.577 2.312,1.744 0.385,0.167 10 ICR+ 2.427,1.577 2.567,1.744 0.140,0.167 10 1 4.486,1.577 4.626,1.744 0.140,0.167 10 5 2.427,2.417 2.567,2.585 0.140,0.167 10 2 4.486,2.417 4.626,2.585 0.140,0.167 10 6 1.928,2.42 2.312,2.587 0.385,0.167 10 ICR- 4.758,1.706 5.143,1.873 0.385,0.167 10 ICR+ 4.758,2.549 5.143,2.716 0.385,0.167 10 ICR- 0.701,3.101 0.969,3.269 0.267,0.167 10 L17 0.701,3.298 2.253,3.465 1.551,0.167 10 Curtain Shield Squib RH 4.826,4.229 5.101,4.396 0.275,0.167 10 L27 4.826,4.426 6.227,4.593 1.400,0.167 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)
a.
U156183E03
1.281,0.219 1.76,0.219 1.76,0.219 1.365,1.073 false 2.094,3.719 2.521,4.073 false 0.177,2.083 2.583,2.49 2.406,0.406 10 false Front view of wire harness connector: (to Curtain Shield Squib RH) 0.292,0.156 1.219,0.51 0.927,0.354 10 false Curtain Shield Squib RH 1.667,1.573 3.073,1.76 1.406,0.188 10 false Center Airbag Sensor 1.677,1.323 1.854,1.5 0.177,0.177 10 false C 1.469,1.323 1.604,1.521 0.135,0.198 10 false D 0.51,3.469 0.823,3.656 0.313,0.188 10 false L17 2.26,3.448 3.156,3.677 0.896,0.229 10 false Connector C 2.552,3.99 2.854,4.135 0.302,0.146 10 false SST

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the curtain shield airbag RH.


d.

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1830, B1831, B1832 or B1833 is not output.


HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the No. 2 floor wire connector (on the curtain shield airbag RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG RH CIRCUIT)
a.
U156185E01
0.1,2.269 2.506,2.674 2.406,0.406 10 Front view of wire harness connector: (to Curtain Shield Squib RH) 0.109,0.306 1.191,0.491 1.082,0.185 10 No. 2 Floor Wire 1.718,1.324 3.125,1.507 1.407,0.184 10 Center Airbag Sensor 1.648,1.079 1.827,1.258 0.179,0.179 10 B 1.282,1.079 1.462,1.258 0.179,0.179 10 C 1.067,1.079 1.206,1.273 0.139,0.194 10 D 1.407,0.401 1.525,0.401 1.525,0.401 1.528,0.858 false 0.618,3.447 0.912,3.603 0.295,0.156 10 L17 2.182,3.462 3.080,3.694 0.899,0.232 10 Connector C 2.226,4.096 2.620,4.237 0.394,0.141 10 ICR- 1.718,3.623 2.194,4.173 false 0.149,1.759 2.341,1.953 2.192,0.194 10 Curtain Shield Squib RH 0.935,0.99 0.935,1.724 false 1.571,3.625 1.095,4.175 false 0.618,4.096 1.014,4.237 0.396,0.141 10 ICR+ 2.049,0.844 2.229,1.024 0.179,0.179 10 A

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L17-1 (ICR+) - Body ground Ignition switch ON Below 1 V
L17-2 (ICR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-1 (ICR+) - L17-2 (ICR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-1 (ICR+) - L17-2 (ICR-) Always 1 MΩ or higher
L17-1 (ICR+) - Body ground Always 1 MΩ or higher
L17-2 (ICR-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146261E18
0.494,1.704 2.037,1.879 1.542,0.174 10 Curtain Shield Squib RH 0.795,1.079 0.371,1.787 0.371,1.787 0.457,1.787 false 0.961,1.16 1.089,1.353 0.128,0.193 10 D 1.099,1.16 1.245,1.344 0.147,0.184 10 C 1.379,1.217 2.738,1.382 1.360,0.165 10 Center Airbag Sensor

Connect the connectors to the curtain shield airbag RH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1830, B1831, B1832 or B1833 is not output.


HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.




OK

NG