The curtain shield squib LH circuit consists of the center airbag sensor and the curtain shield airbag LH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1835/58 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check. ·
A curtain shield squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Curtain shield airbag assembly LH (Curtain shield squib LH) ·
Center airbag sensor assembly |
| B1836/58 | When one of the following conditions is met:
·
The center airbag sensor receives an open circuit signal in the curtain shield squib LH circuit for 2 seconds. ·
A curtain shield squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Curtain shield airbag assembly LH (Curtain shield squib LH) ·
Center airbag sensor assembly |
| B1837/58 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds. ·
A curtain shield squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Curtain shield airbag assembly LH (Curtain shield squib LH) ·
Center airbag sensor assembly |
| B1838/58 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds. ·
A curtain shield squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Curtain shield airbag assembly LH (Curtain shield squib LH) ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the curtain shield airbag LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1835, B1836, B1837 or B1838 is not output.
Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
OK
NG
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K6-1 (ICL+) - Body ground | Ignition switch ON | Below 1 V |
| K6-2 (ICL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K6-1 (ICL+) - K6-2 (ICL-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K6-1 (ICL+) - K6-2 (ICL-) | Always | 1 MΩ or higher |
| K6-1 (ICL+) - Body ground | Always | 1 MΩ or higher |
| K6-2 (ICL-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the curtain shield airbag LH and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1835, B1836, B1837 or B1838 is not output.
Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.
OK
NG