"Door side airbag sensor LH" refer to the side airbag sensor LH.
The side airbag sensor LH or rear airbag sensor RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23 or B1695/16 is stored when a malfunction is detected in the side airbag sensor LH or rear airbag sensor RH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1630/23 | When one of the following conditions is met:
·
A rear airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Rear airbag sensor RH ·
Center airbag sensor assembly |
| B1695/16 | When one of the following conditions is met:
·
A side airbag sensor LH malfunction. ·
A center airbag sensor malfunction. |
·
Side airbag sensor LH ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Turn the ignition switch to ON.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1630 and B1695 are not output | A |
| DTC B1695 is output | B |
| DTC B1630 is output | C |
C
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Temporarily replace the rear airbag sensor RH with a new one.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1630 is not output.
Codes other than DTC B1630 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1690 and B1695 are not output | A |
| DTC B1695 is output | B |
| DTC B1690 is output | C |
Codes other than DTC B1690 and B1695 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C
A
B