Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the center airbag sensor and the driver side knee airbag.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1860/64 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side knee airbag squib circuit during the primary check.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1861/64 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side knee airbag squib circuit for 2 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1862/64 When one of the following conditions is met:
·

The airbag sensor center receives a short circuit to ground signal in the knee airbag (Driver side squib) circuit for 0.5 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1863/64 When one of the following conditions is met:
·

The airbag sensor center receives a short circuit to B+ signal in the knee airbag (Driver side squib) circuit for 0.5 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly



HINT:

Vehicles that are not equipped with knee airbag still contain knee airbag circuits and use substitution parts in replace of the knee airbag. If a malfunction occurs in this knee airbag circuit, DTC B1860/64, B1861/64, B1862/64 or B1863/64 is stored.


WIRING DIAGRAM

C146265E07
0.754,2.937 1.077,3.083 0.323,0.146 10 E24 0.754,3.079 2.762,3.263 2.008,0.184 10 Driver Side Knee Airbag 2.103,1.52 2.397,1.685 0.295,0.165 10 DK+ 2.137,2.52 2.395,2.685 0.258,0.165 10 DK- 2.489,2.313 2.627,2.469 0.137,0.156 10 2 2.492,1.498 2.630,1.691 0.137,0.193 10 1 4.598,1.509 4.727,1.702 0.128,0.193 10 9 4.537,2.314 4.711,2.461 0.174,0.147 10 10 4.817,1.585 5.131,1.759 0.313,0.174 10 DK+ 4.817,2.416 5.131,2.590 0.313,0.174 10 DK- 4.907,4.079 5.202,4.226 0.295,0.147 10 E47 4.908,4.24 6.286,4.433 1.378,0.193 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK DRIVER SIDE KNEE AIRBAG (DRIVER SIDE KNEE SQUIB)
a.
U164499E02
1.99,3.719 2.417,3.875 false 0.917,0.635 0.75,1.667 0.75,1.667 0.885,1.667 false 0.271,2.146 2.625,2.521 2.354,0.375 10 false Front view of wire harness connector: (to Driver Side Knee Squib) 1.583,1.094 2.969,1.313 1.385,0.219 10 false Center Airbag Sensor 0.958,1.594 2.479,1.813 1.521,0.219 10 false Driver Side Knee Squib 1.042,0.708 1.177,0.865 0.135,0.156 10 false D 1.25,0.708 1.375,0.865 0.125,0.156 10 false C 2.177,3.104 3.01,3.271 0.833,0.167 10 false Connector C 2.469,3.823 2.802,3.99 0.333,0.167 10 false SST 0.406,3.531 0.719,3.719 0.313,0.188 10 false E24

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side knee airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the driver side knee airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT)
a.
U164502E01
0.277,2.315 2.627,2.656 2.350,0.341 10 Front view of wire harness connector: (to Driver Side Knee Squib) 1.602,1.107 3.003,1.449 1.402,0.342 10 Center Airbag Sensor 1.179,1.696 2.668,1.852 1.489,0.156 10 Driver Side Knee Squib 1.097,0.635 1.005,1.797 1.005,1.797 1.132,1.797 false 1.209,0.704 1.346,0.878 0.137,0.174 10 D 1.395,0.704 1.551,0.850 0.156,0.147 10 C 2.133,0.498 2.270,0.663 0.137,0.165 10 A 1.772,0.709 1.911,0.893 0.139,0.184 10 B 2.134,3.366 3.077,3.522 0.943,0.156 10 Connector C 2.182,3.881 2.498,4.023 0.316,0.142 10 DK- 0.532,3.881 0.848,4.023 0.316,0.142 10 DK+ 0.902,3.916 1.426,3.804 false 1.598,3.804 2.157,3.916 false 0.559,3.503 0.835,3.652 0.276,0.149 10 E24 0.029,0.026 1.445,0.182 1.415,0.156 10 Instrument Panel Wire 1.76,0.112 1.876,0.112 1.876,0.112 1.651,0.504 false 1.783,0.492 1.829,0.447 false 1.783,0.554 1.884,0.453 false 1.783,0.615 1.884,0.514 false 1.783,0.677 1.884,0.576 false 1.837,0.685 1.884,0.638 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E24-1 (DK+) - Body ground Ignition switch ON Below 1 V
E24-2 (DK-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-1 (DK+) - E24-2 (DK-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-1 (DK+) - E24-2 (DK-) Always 1 MΩ or higher
E24-1 (DK+) - Body ground Always 1 MΩ or higher
E24-2 (DK-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146268E01
0.525,1.66 2.107,1.836 1.582,0.177 10 Driver Side Knee Squib 1.378,1.259 2.765,1.443 1.387,0.184 10 Center Airbag Sensor 0.876,0.739 0.36,1.724 0.36,1.724 0.452,1.724 false 0.968,0.835 1.124,1.000 0.156,0.165 10 D 1.105,0.837 1.261,1.012 0.156,0.174 10 C

Connect the connectors to the driver side knee airbag and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.




OK

NG