The driver side knee airbag squib circuit consists of the center airbag sensor and the driver side knee airbag.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1860/64 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal 5 times in the driver side knee airbag squib circuit during the primary check. ·
A driver side knee airbag squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Driver side knee airbag assembly (Driver side knee squib) ·
Center airbag sensor assembly |
| B1861/64 | When one of the following conditions is met:
·
The center airbag sensor receives an open circuit signal in the driver side knee airbag squib circuit for 2 seconds. ·
A driver side knee airbag squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Driver side knee airbag assembly (Driver side knee squib) ·
Center airbag sensor assembly |
| B1862/64 | When one of the following conditions is met:
·
The airbag sensor center receives a short circuit to ground signal in the knee airbag (Driver side squib) circuit for 0.5 seconds. ·
A driver side knee airbag squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Driver side knee airbag assembly (Driver side knee squib) ·
Center airbag sensor assembly |
| B1863/64 | When one of the following conditions is met:
·
The airbag sensor center receives a short circuit to B+ signal in the knee airbag (Driver side squib) circuit for 0.5 seconds. ·
A driver side knee airbag squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Driver side knee airbag assembly (Driver side knee squib) ·
Center airbag sensor assembly |
Vehicles that are not equipped with knee airbag still contain knee airbag circuits and use substitution parts in replace of the knee airbag. If a malfunction occurs in this knee airbag circuit, DTC B1860/64, B1861/64, B1862/64 or B1863/64 is stored.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side knee airbag.
Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the driver side knee airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1860, B1861, B1862 or B1863 is not output.
Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.
OK
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY(for Driver Side)>REMOVAL)
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
OK
NG
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E24-1 (DK+) - Body ground | Ignition switch ON | Below 1 V |
| E24-2 (DK-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E24-1 (DK+) - E24-2 (DK-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E24-1 (DK+) - E24-2 (DK-) | Always | 1 MΩ or higher |
| E24-1 (DK+) - Body ground | Always | 1 MΩ or higher |
| E24-2 (DK-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the driver side knee airbag and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1860, B1861, B1862 or B1863 is not output.
Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.
OK
NG