Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1865/65  Short in Front Passenger Side Knee Airbag Squib Circuit  B1866/65  Open in Front Passenger Side Knee Airbag Squib Circuit  B1867/65  Short to GND in Front Passenger Side Knee Airbag Squib Circuit  B1868/65  Short to B+ in Front Passenger Side Knee Airbag Squib Circuit  


DESCRIPTION

The front passenger side knee airbag squib circuit consists of the center airbag sensor and the front passenger side knee airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1865/65 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front passenger side knee airbag squib circuit during the primary check.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1866/65 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front passenger side knee airbag squib circuit for 2 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1867/65 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front passenger side knee airbag squib circuit for 0.5 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1868/65 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front passenger side knee airbag squib circuit for 0.5 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly



HINT:

Vehicles that are not equipped with knee airbag still contain knee airbag circuits and use substitution parts in replace of the knee airbag. If a malfunction occurs in this knee airbag circuit, DTC B1865/65, B1866/65, B1867/65 or B1868/65 is stored.


WIRING DIAGRAM

C146265E08
0.754,2.937 1.077,3.091 0.323,0.154 10 E40 0.754,3.091 3.382,3.275 2.628,0.184 10 Front Passenger Side Knee Airbag 2.103,1.52 2.397,1.685 0.295,0.165 10 PK+ 2.137,2.52 2.395,2.685 0.258,0.165 10 PK- 2.475,2.271 2.613,2.427 0.137,0.156 10 2 2.464,1.484 2.602,1.677 0.137,0.193 10 1 4.517,1.509 4.714,1.702 0.198,0.193 10 19 4.537,2.314 4.711,2.461 0.174,0.147 10 20 4.817,1.585 5.131,1.759 0.313,0.174 10 PK+ 4.817,2.416 5.131,2.590 0.313,0.174 10 PK- 4.907,4.079 5.202,4.226 0.295,0.147 10 E47 4.908,4.24 6.286,4.433 1.378,0.193 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT PASSENGER SIDE KNEE AIRBAG (FRONT PASSENGER SIDE KNEE SQUIB)
a.
U164500E02
1.99,3.771 2.417,3.917 false 0.927,0.656 0.927,1.604 false 0.156,2.229 2.552,2.583 2.396,0.354 10 false Front view of wire harness connector: (to Front Passenger Side Knee Squib) 1.625,1.073 3.021,1.406 1.396,0.333 10 false Center Airbag Sensor 0.219,1.594 2.365,1.802 2.146,0.208 10 false Front Passenger Side Knee Squib 1.031,0.719 1.167,0.875 0.135,0.156 10 false D 1.24,0.719 1.365,0.875 0.125,0.156 10 false C 2.177,3.198 3.01,3.365 0.833,0.167 10 false Connector C 2.438,3.865 2.771,4.031 0.333,0.167 10 false SST 0.448,3.583 0.771,3.792 0.323,0.208 10 false E40

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front passenger side knee airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front passenger side knee airbag (front passenger side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the instrument panel wire connector (on the front passenger side knee airbag side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER KNEE SQUIB CIRCUIT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER KNEE SQUIB CIRCUIT)
a.
U164501E01
0.168,2.468 2.542,2.832 2.375,0.363 10 Front view of wire harness connector: (to Front Passenger Side Knee Squib) 1.691,1.078 3.086,1.259 1.394,0.181 10 Center Airbag Sensor 0.688,1.661 2.816,1.862 2.128,0.201 10 Front Passenger Side Knee Squib 1.209,0.709 1.346,0.883 0.137,0.174 10 D 1.395,0.709 1.551,0.855 0.156,0.147 10 C 2.133,0.502 2.270,0.668 0.137,0.165 10 A 1.772,0.714 1.911,0.898 0.139,0.184 10 B 2.138,3.436 3.081,3.592 0.943,0.156 10 Connector C 2.187,3.879 2.503,4.021 0.316,0.142 10 PK- 0.537,3.879 0.853,4.021 0.316,0.142 10 PK+ 0.907,3.913 1.431,3.802 false 1.603,3.802 2.161,3.913 false 0.593,3.501 0.878,3.650 0.286,0.149 10 E40 0.037,0.032 1.439,0.211 1.401,0.179 10 Instrument Panel Wire 1.773,0.118 1.894,0.118 1.894,0.118 1.682,0.496 false 1.782,0.493 1.827,0.447 false 1.782,0.554 1.883,0.453 false 1.782,0.616 1.883,0.515 false 1.782,0.677 1.883,0.577 false 1.836,0.685 1.883,0.638 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E40-1 (PK+) - Body ground Ignition switch ON Below 1 V
E40-2 (PK-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E40-1 (PK+) - E40-2 (PK-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E40-1 (PK+) - E40-2 (PK-) Always 1 MΩ or higher
E40-1 (PK+) - Body ground Always 1 MΩ or higher
E40-2 (PK-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146268E05
0.108,1.675 2.263,1.824 2.156,0.149 10 Front Passenger Side Knee Squib 1.504,1.257 2.901,1.457 1.397,0.200 10 Center Airbag Sensor 0.876,1.675 0.876,0.773 false 0.968,0.83 1.124,0.996 0.156,0.165 10 D 1.105,0.833 1.261,1.007 0.156,0.174 10 C

Connect the connectors to the front passenger side knee airbag and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.




OK

NG