Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1920/77  Short in Rear Pretensioner Squib RH Circuit  B1921/77  Open in Rear Pretensioner Squib RH Circuit  B1922/77  Short to GND in Rear Pretensioner Squib RH Circuit  B1923/77  Short to B+ in Rear Pretensioner Squib RH Circuit  


DESCRIPTION

The rear pretensioner squib RH circuit consists of the center airbag sensor and the rear seat outer belt RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

Theses DTCs are stored when a malfunction is detected in the rear pretensioner squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1920/77 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the rear pretensioner squib RH circuit during the primary check.

·

A rear pretensioner squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat outer belt assembly RH (Rear pretensioner squib RH)

·

Center airbag sensor assembly


B1921/77 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the rear pretensioner squib RH circuit for 2 seconds.

·

A rear pretensioner squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat outer belt assembly RH (Rear pretensioner squib RH)

·

Center airbag sensor assembly


B1922/77 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the rear pretensioner squib RH circuit for 0.5 seconds.

·

A rear pretensioner squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat outer belt assembly RH (Rear pretensioner squib RH)

·

Center airbag sensor assembly


B1923/77 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the rear pretensioner squib RH circuit for 0.5 seconds.

·

A rear pretensioner squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat outer belt assembly RH (Rear pretensioner squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E11
4.762,2.554 5.200,2.719 0.437,0.165 10 PRR- 4.762,1.7 5.290,1.865 0.528,0.165 10 PRR+ 2.031,2.435 2.339,2.600 0.309,0.165 10 RR- 1.989,1.595 2.339,1.759 0.351,0.165 10 RR+ 2.439,2.395 2.641,2.575 0.203,0.181 10 2 2.439,1.541 2.641,1.722 0.203,0.181 10 1 0.604,3.256 2.808,3.433 2.204,0.177 10 Rear Pretensioner Squib LH 0.604,3.093 0.945,3.231 0.341,0.138 10 L14 4.84,4.326 6.237,4.503 1.398,0.177 10 Center Airbag Sensor 4.84,4.177 5.180,4.315 0.341,0.138 10 L27 4.522,1.617 4.744,1.782 0.222,0.166 10 1 4.522,2.431 4.744,2.597 0.222,0.166 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION ).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK REAR SEAT OUTER BELT RH (REAR PRETENSIONER SQUIB RH)
a.
U164761E01
0.078,2.16 2.452,2.528 2.374,0.368 10 Front view of wire harness connector: (to Rear Pretensioner Squib RH) 1.571,1.245 2.939,1.398 1.368,0.152 10 Center Airbag Sensor 0.988,1.206 1.115,1.364 0.126,0.158 10 D 1.199,1.206 1.325,1.364 0.126,0.158 10 C 0.567,1.679 2.480,1.842 1.913,0.163 10 Rear Pretensioner Squib RH 0.812,1.093 0.412,1.765 0.412,1.765 0.507,1.765 false 2.227,3.297 3.076,3.454 0.849,0.157 10 Connector C 2.441,3.682 2.777,3.851 0.336,0.170 10 SST 0.526,3.282 0.830,3.469 0.304,0.187 10 L14 2.141,3.556 2.415,3.75 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the rear seat outer belt RH.


d.

Connect the yellow wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the rear seat outer belt RH (rear pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1920, B1921, B1922 or B1923 is not output.


HINT:

Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.




OK

REPLACE REAR SEAT OUTER BELT ASSEMBLY RH

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the No. 2 floor wire connector (on the rear seat outer belt RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK NO. 2 FLOOR WIRE (REAR PRETENSIONER SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (REAR PRETENSIONER SQUIB RH CIRCUIT)
a.
U164764E02
1.292,0.542 1.385,0.542 1.385,0.542 1.219,1.01 false 0.594,1.104 0.521,1.729 0.521,1.729 0.646,1.729 false 1.708,3.219 2.146,3.615 false 1.594,3.219 1.146,3.615 false 1.365,0.979 1.406,0.938 false 1.365,1.031 1.458,0.938 false 1.375,1.083 1.469,0.979 false 1.375,1.146 1.469,1.042 false 1.406,1.177 1.448,1.125 false 0.094,2.208 2.417,2.573 2.323,0.365 10 false Front view of wire harness connector: (to Rear Pretensioner Squib RH) 2.073,3.063 2.927,3.229 0.854,0.167 10 false Connector C 1.594,1.292 3,1.469 1.406,0.177 10 false Center Airbag Sensor 0.219,0.479 1.281,0.667 1.063,0.188 10 false No. 2 Floor Wire 0.708,1.646 2.51,1.833 1.802,0.188 10 false Rear Pretensioner Squib RH 1.74,0.979 1.896,1.125 0.156,0.146 10 false A 1.385,1.198 1.542,1.344 0.156,0.146 10 false B 1,1.198 1.156,1.344 0.156,0.146 10 false C 0.792,1.198 0.948,1.344 0.156,0.146 10 false D 0.833,3.146 1.156,3.323 0.323,0.177 10 false L14 0.771,3.542 1.146,3.677 0.375,0.135 10 false RR+ 2.198,3.542 2.5,3.708 0.302,0.167 10 false RR-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L14-1 (RR+) - Body ground Ignition switch ON Below 1 V
L14-2 (RR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-1 (RR+) - L14-2 (RR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-1 (RR+) - L14-2 (RR-) Always 1 MΩ or higher
L14-1 (RR+) - Body ground Always 1 MΩ or higher
L14-2 (RR-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146261E76
0.865,1.115 0.792,1.615 false 0.156,1.615 2.01,1.792 1.854,0.177 10 false Rear Pretensioner Squib RH 1.51,1.25 2.896,1.438 1.385,0.188 10 false Center Airbag Sensor 0.979,1.177 1.313,1.375 0.333,0.198 10 false D 1.104,1.188 1.271,1.396 0.167,0.208 10 false C

Connect the connectors to the rear seat outer belt RH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1920, B1921, B1922 or B1923 is not output.


HINT:

Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.




OK

NG