Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1925/78  Short in Rear Pretensioner Squib LH Circuit  B1926/78  Open in Rear Pretensioner Squib LH Circuit  B1927/78  Short to GND in Rear Pretensioner Squib LH Circuit  B1928/78  Short to B+ in Rear Pretensioner Squib LH Circuit  


DESCRIPTION

The rear pretensioner squib LH circuit consists of the center airbag sensor and the rear seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1925/78 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the rear pretensioner squib LH circuit during the primary check.

·

A rear pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat outer belt assembly LH (Rear pretensioner squib LH)

·

Center airbag sensor assembly


B1926/78 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the rear pretensioner squib LH circuit for 2 seconds.

·

A rear pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat outer belt assembly LH (Rear pretensioner squib LH)

·

Center airbag sensor assembly


B1927/78 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the rear pretensioner squib LH circuit for 0.5 seconds.

·

A rear pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat outer belt assembly LH (Rear pretensioner squib LH)

·

Center airbag sensor assembly


B1928/78 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the rear pretensioner squib LH circuit for 0.5 seconds.

·

A rear pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat outer belt assembly LH (rear pretensioner squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E12
4.762,2.554 5.200,2.719 0.437,0.165 10 PLR- 4.762,1.7 5.290,1.865 0.528,0.165 10 PLR+ 2.031,2.435 2.339,2.600 0.309,0.165 10 RL- 1.989,1.595 2.339,1.759 0.351,0.165 10 RL+ 2.439,2.395 2.641,2.575 0.203,0.181 10 2 2.439,1.541 2.641,1.722 0.203,0.181 10 1 0.604,3.256 2.808,3.433 2.204,0.177 10 Rear Pretensioner Squib LH 0.604,3.093 0.945,3.231 0.341,0.138 10 K13 4.84,4.326 6.237,4.503 1.398,0.177 10 Center Airbag Sensor 4.84,4.177 5.180,4.315 0.341,0.138 10 K27 4.522,1.617 4.744,1.782 0.222,0.166 10 8 4.522,2.431 4.744,2.597 0.222,0.166 10 7

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK REAR SEAT OUTER BELT LH (REAR PRETENSIONER SQUIB LH)
a.
U164765E03
0.813,0.479 0.74,1.698 0.74,1.698 0.896,1.698 false 2.125,3.479 2.521,3.646 false 1.583,1.271 2.99,1.479 1.406,0.208 10 false Center Airbag Sensor 1.219,0.625 1.375,0.781 0.156,0.156 10 false C 1.01,0.615 1.167,0.771 0.156,0.156 10 false D 0.948,1.615 2.74,1.781 1.792,0.167 10 false Rear Pretensioner Squib LH 0.073,2.104 2.469,2.458 2.396,0.354 10 false Front view of wire harness connector: (to Rear Pretensioner Squib LH) 0.563,3.292 0.875,3.49 0.313,0.198 10 false K13 2.313,3.104 3.135,3.271 0.823,0.167 10 false Connector C 2.583,3.594 3.01,3.781 0.427,0.188 10 false SST

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the rear seat outer belt LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the rear seat outer belt LH (rear pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1925, B1926, B1927 or B1928 is not output.


HINT:

Codes other than DTC B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.




OK

REPLACE REAR SEAT OUTER BELT ASSEMBLY LH

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the rear seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not damaged or deformed.




OK

3.CHECK FLOOR WIRE (REAR PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (REAR PRETENSIONER SQUIB LH CIRCUIT)
a.
U164766E02
1.083,0.104 1.177,0.104 1.177,0.104 1.25,0.406 false 0.594,0.479 0.479,1.688 0.479,1.688 0.656,1.688 false 1.719,3.24 2.229,3.771 false 1.583,3.229 1.083,3.76 false 1.375,0.406 1.417,0.365 false 1.365,0.469 1.469,0.365 false 1.365,0.531 1.469,0.417 false 1.365,0.583 1.469,0.479 false 1.406,0.594 1.458,0.542 false 0.406,0.042 1.073,0.208 0.667,0.167 10 false Floor Wire 1.75,0.375 1.875,0.542 0.125,0.167 10 false A 1.365,0.615 1.49,0.781 0.125,0.167 10 false B 0.99,0.604 1.115,0.771 0.125,0.167 10 false C 0.781,0.615 0.906,0.781 0.125,0.167 10 false D 1.615,1.281 2.99,1.438 1.375,0.156 10 false Center Airbag Sensor 0.688,1.594 2.49,1.74 1.802,0.146 10 false Rear Pretensioner Squib LH 0.073,2.104 2.427,2.479 2.354,0.375 10 false Front view of wire harness connector: (to Rear Pretensioner Squib LH) 2.167,3.094 3.021,3.26 0.854,0.167 10 false Connector C 0.646,3.125 0.969,3.292 0.323,0.167 10 false K13 0.802,3.719 1.125,3.906 0.323,0.188 10 false RL+ 2.292,3.719 2.583,3.906 0.292,0.188 10 false RL-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K13-1 (RL+) - Body ground Ignition switch ON Below 1 V
K13-2 (RL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K13-1 (RL+) - K13-2 (RL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K13-1 (RL+) - K13-2 (RL-) Always 1 MΩ or higher
K13-1 (RL+) - Body ground Always 1 MΩ or higher
K13-2 (RL-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C148850E06
0.885,0.521 0.406,1.76 0.406,1.76 0.563,1.76 false 0.979,0.604 1.208,0.823 0.229,0.219 10 false D 1.094,0.604 1.313,0.792 0.219,0.188 10 false C 1.521,1.271 2.917,1.458 1.396,0.188 10 false Center Airbag Sensor 0.625,1.667 2.448,1.844 1.823,0.177 10 false Rear Pretensioner Squib LH

Connect the connectors to the rear seat outer belt LH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1925, B1926, B1927 or B1928 is not output.


HINT:

Codes other than DTC B1925, B1926, B1927 or B1928 may be output at this time, but they are not related to this check.




OK

NG