Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1697/82  Lost Communication with Door Side Airbag Sensor LH  B1698/82  Door Side Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

HINT:

"Door side airbag sensor LH" refer to the side airbag sensor LH.


·

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH, and rear airbag sensor LH or RH.

The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1632/81 or B1697/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH).


DTC Code DTC Detection Condition Trouble Area
B1632/81 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat airbag RH and curtain shield airbag RH) for 2 seconds.

·

A side airbag sensor RH malfunction.

·

A rear airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front door wire RH

·

Side airbag sensor RH

·

Rear airbag sensor RH

·

Center airbag sensor assembly


B1633/81 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat airbag RH and curtain shield airbag RH) for 2 seconds.

·

A side airbag sensor RH malfunction.

·

A rear airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front door wire RH

·

Side airbag sensor RH

·

Rear airbag sensor RH

·

Center airbag sensor assembly


B1697/82 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat airbag LH and curtain shield airbag LH) for 2 seconds.

·

A side airbag sensor LH malfunction.

·

A rear airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front door wire LH

·

Side airbag sensor LH

·

Rear airbag sensor LH

·

Center airbag sensor assembly


B1698/82 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat airbag LH and curtain shield airbag LH) for 2 seconds.

·

A side airbag sensor LH malfunction.

·

A rear airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front door wire LH

·

Side airbag sensor LH

·

Rear airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C175144E02
1.198,0.988 1.624,1.158 0.427,0.170 10 BBR+ 0.1,0.009 1.189,0.253 1.089,0.244 12 for RH Side: 1.71,0.898 1.873,1.068 0.163,0.170 10 4 5.432,0.898 5.636,1.068 0.204,0.170 10 17 5.432,1.706 5.636,1.876 0.204,0.170 10 18 1.71,1.697 1.873,1.866 0.163,0.170 10 3 3.456,0.757 3.619,0.926 0.163,0.170 10 4 3.456,1.555 3.619,1.725 0.163,0.170 10 3 1.71,3.083 1.873,3.253 0.163,0.170 10 1 3.671,3.083 3.834,3.253 0.163,0.170 10 2 1.71,3.868 1.873,4.038 0.163,0.170 10 2 3.677,3.868 3.840,4.038 0.163,0.170 10 1 2.617,2.947 2.780,3.117 0.163,0.170 10 2 2.623,3.732 2.786,3.902 0.163,0.170 10 1 1.198,1.787 1.624,1.956 0.427,0.170 10 BBR- 3.415,0.986 3.684,1.156 0.269,0.170 10 IL1 3.415,1.77 3.684,1.940 0.269,0.170 10 IL1 2.582,3.182 2.852,3.352 0.269,0.170 10 IL1 2.582,3.967 2.852,4.136 0.269,0.170 10 IL1 5.718,0.988 6.145,1.158 0.427,0.170 10 BBR+ 5.718,1.787 6.145,1.956 0.427,0.170 10 BBR- 1.198,3.192 1.624,3.362 0.427,0.170 10 BCR+ 0.551,4.679 0.797,4.849 0.246,0.170 10 I9 0.544,4.847 2.359,5.017 1.816,0.170 10 Side Airbag Sensor RH 3.764,4.679 4.073,4.849 0.309,0.170 10 L18 3.757,4.847 5.302,5.017 1.545,0.170 10 Rear Airbag Sensor RH 5.585,4.679 5.894,4.849 0.309,0.170 10 L27 5.578,4.847 6.975,5.017 1.397,0.170 10 Center Airbag Sensor 3.902,3.192 4.328,3.362 0.427,0.170 10 BCR+ 1.198,3.962 1.624,4.132 0.427,0.170 10 BCR- 3.916,3.962 4.342,4.132 0.427,0.170 10 BCR-

C175145E02
1.183,0.99 1.610,1.159 0.427,0.170 10 BBL+ 0.084,0.029 1.094,0.199 1.010,0.170 12 for LH Side: 1.695,0.899 1.858,1.069 0.163,0.170 10 4 5.417,0.899 5.622,1.069 0.204,0.170 10 24 5.417,1.707 5.622,1.877 0.204,0.170 10 23 1.695,1.698 1.858,1.868 0.163,0.170 10 3 1.695,3.085 1.858,3.255 0.163,0.170 10 1 3.657,3.085 3.820,3.255 0.163,0.170 10 2 1.695,3.869 1.858,4.039 0.163,0.170 10 2 3.663,3.869 3.826,4.039 0.163,0.170 10 1 2.697,2.945 2.860,3.115 0.163,0.170 10 2 2.703,3.729 2.866,3.899 0.163,0.170 10 1 1.183,1.788 1.610,1.958 0.427,0.170 10 BBL- 5.685,0.99 6.112,1.159 0.427,0.170 10 BBL+ 5.685,1.788 6.112,1.958 0.427,0.170 10 BBL- 1.183,3.193 1.610,3.363 0.427,0.170 10 BCL+ 0.536,4.681 0.782,4.851 0.246,0.170 10 K7 0.529,4.849 2.058,5.019 1.529,0.170 10 Rear Airbag Sensor LH 3.714,4.681 4.023,4.851 0.309,0.170 10 I19 3.693,4.849 5.218,5.019 1.525,0.170 10 Side Airbag Sensor LH 5.571,4.681 5.879,4.851 0.309,0.170 10 K27 5.564,4.849 6.960,5.019 1.397,0.170 10 Center Airbag Sensor 3.887,3.193 4.314,3.363 0.427,0.170 10 BCL+ 2.648,3.193 2.901,3.363 0.253,0.170 10 IK1 2.648,3.971 2.901,4.141 0.253,0.170 10 IK1 1.183,3.964 1.610,4.134 0.427,0.170 10 BCL- 3.901,3.964 4.328,4.134 0.427,0.170 10 BCL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1632, B1633, B1697 and B1698 are not output A
DTC B1697 or B1698 is output B
DTC B1632 or B1633 is output C

HINT:

Codes other than DTC B1632, B1633, B1697 and B1698 may be output at this time, but they are not related to this check.




C

2.CHECK CONNECTION OF CONNECTORS

A

B

8.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor RH and rear airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side, the rear airbag sensor RH side and side airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK SIDE AIRBAG SENSOR RH

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK SIDE AIRBAG SENSOR RH
a.
C171827E09
0.6,1.423 1.383,1.738 0.783,0.316 10 Side Airbag Sensor LH 2.127,1.209 3.075,1.525 0.948,0.316 10 Center Airbag Sensor

Connect the connectors to the center airbag sensor.


b.

Interchange the side airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1632, B1633, B1697 and B1698 are not output A
DTC B1697 or B1698 is output B
DTC B1632 or B1633 is output C

HINT:

Codes other than DTC B1632, B1633, B1697 and B1698 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

5.CHECK REAR AIRBAG SENSOR RH CIRCUIT

A

B

5.CHECK REAR AIRBAG SENSOR RH CIRCUIT
a.

Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

U164804E01
0.122,1.528 0.931,1.883 0.809,0.355 10 Rear Airbag Sensor RH 1.547,1.528 2.351,1.883 0.804,0.355 10 Side Airbag Sensor RH 1.752,1.084 1.876,1.254 0.123,0.170 10 A 0.594,1.052 0.718,1.221 0.123,0.170 10 F 1.425,1.29 1.549,1.460 0.123,0.170 10 B 1.248,1.29 1.371,1.460 0.123,0.170 10 C 1.136,1.29 1.259,1.460 0.123,0.170 10 D 0.935,1.29 1.059,1.460 0.123,0.170 10 E 4.898,1.402 5.040,1.572 0.142,0.170 10 I9 2.711,1.402 2.966,1.572 0.255,0.170 10 L18 2.378,0.365 4.705,0.716 2.327,0.350 10 Front view of wire harness connector: (to Rear Airbag Sensor RH) 4.83,0.365 7.157,0.716 2.327,0.350 10 Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.011,1.655 4.824,1.839 0.812,0.184 10 Connector E 6.127,1.655 6.939,1.839 0.812,0.184 10 Connector B 4.114,1.953 4.535,2.137 0.421,0.184 10 BCR+ 4.945,2.219 5.319,2.403 0.375,0.184 10 BCR- 2.818,2.079 3.238,2.249 0.420,0.170 10 BCR- 6.101,2.247 6.520,2.417 0.420,0.170 10 BCR+ 3.769,2.359 4.598,2.512 0.829,0.152 10 Service Wire 3.493,1.731 3.078,2.044 false 3.661,1.724 4.081,2.016 false 3.664,2.059 4.084,2.351 false 5.688,1.797 5.125,2.194 false 5.792,1.794 6.199,2.226 false


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-1 (BCR+) - Body ground Ignition switch ON Below 1 V
I9-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always 1 MΩ or higher
I9-1 (BCR+) - Body ground Always 1 MΩ or higher
I9-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

6.CHECK REAR AIRBAG SENSOR RH

NG

7.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
6.CHECK REAR AIRBAG SENSOR RH
a.
C171828E08
0.469,1.174 1.236,1.545 0.767,0.371 10 Rear Airbag Sensor RH 2.119,1.174 2.867,1.524 0.749,0.350 10 Side Airbag Sensor RH

Connect the connectors to the center airbag sensor.


b.

Temporarily replace the rear airbag sensor RH with a new one.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1632 and B1633 is not output.


HINT:

Codes other than DTC B1632 and B1633 may be output at this time, but they are not related to this check.




OK

NG

7.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
a.

Disconnect the front door wire RH connectors from the No. 2 floor wire.

U164668E02
3.125,1.927 2.823,2.26 false 3.323,1.927 3.646,2.24 false 3.26,2.219 3.51,2.479 false 5.688,1.771 5.125,2.125 false 5.771,1.771 6.188,2.198 false 0.979,1.094 0.979,0.135 0.979,0.135 0.865,0.135 false 1.406,1.073 1.406,0.094 1.406,0.094 1.469,0.094 false 0.115,0.063 0.823,0.375 0.708,0.313 10 false No. 2 Floor Wire 1.531,0.052 2.292,0.375 0.76,0.323 10 false Front Door Wire RH 0.063,1.542 0.854,1.906 0.792,0.365 10 false Rear Airbag Sensor RH 1.635,1.552 2.469,1.906 0.833,0.354 10 false Side Airbag Sensor RH 1.802,1.063 1.938,1.229 0.135,0.167 10 false A 0.5,1.083 0.635,1.25 0.135,0.167 10 false F 1.531,1.26 1.667,1.427 0.135,0.167 10 false B 1.229,1.271 1.365,1.438 0.135,0.167 10 false C 1.094,1.271 1.229,1.438 0.135,0.167 10 false D 0.792,1.271 0.927,1.438 0.135,0.167 10 false E 2.552,1.281 2.844,1.458 0.292,0.177 10 false IL1 2.385,0.24 4.813,0.583 2.427,0.344 10 false Front view of wire harness connector: (to No. 2 Floor Wire) 4.813,0.24 7.146,0.583 2.333,0.344 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 3.656,1.625 4.552,1.813 0.896,0.188 10 false Connector C 4.99,1.281 5.219,1.458 0.229,0.177 10 false I9 6.104,1.625 7,1.813 0.896,0.188 10 false Connector B 3.708,2.198 4.125,2.354 0.417,0.156 10 false BCR+ 4.813,2.125 5.229,2.281 0.417,0.156 10 false BCR- 2.396,2.198 2.813,2.354 0.417,0.156 10 false BCR- 6.177,2.198 6.594,2.354 0.417,0.156 10 false BCR+ 3.479,2.5 4.323,2.677 0.844,0.177 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-1 (BCR+) - Body ground Ignition switch ON Below 1 V
I9-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always 1 MΩ or higher
I9-1 (BCR+) - Body ground Always 1 MΩ or higher
I9-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor LH and rear airbag sensor LH.

OK:

The connectors are properly connected.




OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor, side airbag sensor LH and rear airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side, the rear airbag sensor LH side and side airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

10.CHECK REAR AIRBAG SENSOR LH

NG

REPLACE HARNESS AND CONNECTOR

10.CHECK REAR AIRBAG SENSOR LH
a.
C146229E21
0.139,1.689 1.670,1.859 1.531,0.170 10 Rear Airbag Sensor LH 1.682,1.303 3.053,1.468 1.371,0.165 10 Center Airbag Sensor 0.917,0.888 0.917,1.641 false

Connect the connector to the center airbag sensor.


b.

Temporarily replace the rear airbag sensor LH with a new one.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1697 and B1698 are not output.


HINT:

Codes other than DTC B1697 and B1698 may be output at this time, but they are not related to this check.




OK

NG

11.CHECK SIDE AIRBAG SENSOR LH CIRCUIT
11.CHECK SIDE AIRBAG SENSOR LH CIRCUIT
a.

Turn the ignition switch off.

U164659E01
0.112,1.48 0.886,1.851 0.774,0.371 10 Side Airbag Sensor LH 1.398,1.231 1.514,1.401 0.116,0.170 10 B 1.213,1.231 1.353,1.401 0.140,0.170 10 C 1.115,1.231 1.255,1.401 0.140,0.170 10 D 0.93,1.231 1.071,1.401 0.140,0.170 10 E 0.612,1.044 0.753,1.214 0.140,0.170 10 F 1.713,1.045 1.917,1.250 0.205,0.205 10 A 1.542,1.466 2.346,1.816 0.804,0.350 10 Rear Airbag Sensor LH 2.347,0.312 4.704,0.621 2.357,0.309 10 Rear view of wire harness connector: (to Side Airbag Sensor LH) 4.842,0.312 7.150,0.621 2.309,0.309 10 Rear view of wire harness connector: (to Rear Airbag Sensor LH) 3.681,1.51 4.552,1.680 0.871,0.170 10 Connector E 6.154,1.559 7.025,1.729 0.871,0.170 10 Connector B 2.539,1.172 2.840,1.335 0.302,0.163 10 I19 4.96,1.196 5.262,1.359 0.302,0.163 10 K7 2.505,2.259 2.939,2.442 0.434,0.184 10 BCL+ 3.794,2.108 4.228,2.291 0.434,0.184 10 BCL- 6.084,2.334 6.518,2.517 0.434,0.184 10 BCL+ 5.166,2.36 5.600,2.544 0.434,0.184 10 BCL- 3.099,1.786 2.751,2.238 false 3.195,1.782 3.766,2.164 false 3.401,2.421 4.244,2.591 0.843,0.170 10 Service Wire 3.233,2.071 3.485,2.4 false 5.706,1.771 5.376,2.346 false 5.776,1.772 6.196,2.313 false


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified condition
K7-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K7-2 (BCL-) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always Below 1 Ω



j.

Disconnect the service wire from connector E.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - Body ground Always 1 MΩ or higher
K7-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

12.CHECK SIDE AIRBAG SENSOR LH

NG

13.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
12.CHECK SIDE AIRBAG SENSOR LH
a.
C171828E09
0.421,1.174 1.197,1.545 0.776,0.371 10 Side Airbag Sensor RH 2.141,1.174 3.018,1.524 0.877,0.350 10 Rear Airbag Sensor LH

Connect the connectors to the rear airbag sensor LH.


b.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1632, B1633, B1697 and B1698 are not output A
DTC B1632 or B1633 is output B
DTC B1697 or B1698 is output C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B

13.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
a.

Disconnect the floor wire connector from the front door wire LH.

U164669E02
3.104,1.698 2.823,2.271 false 3.333,1.708 3.771,2.104 false 3.292,2.188 3.51,2.5 false 5.688,1.781 5.125,2.135 false 5.802,1.771 6.219,2.198 false 0.979,1.083 0.979,0.125 0.979,0.125 0.865,0.125 false 1.417,1.094 1.417,0.125 1.417,0.125 1.479,0.125 false 0.156,0.052 0.865,0.365 0.708,0.313 10 false Front Door Wire LH 1.563,0.052 2.271,0.25 0.708,0.198 10 false Floor Wire 0.063,1.552 0.854,1.917 0.792,0.365 10 false Side Airbag Sensor LH 1.552,1.563 2.479,1.917 0.927,0.354 10 false Rear Airbag Sensor LH 1.802,1.073 1.938,1.24 0.135,0.167 10 false A 0.5,1.063 0.635,1.229 0.135,0.167 10 false F 1.542,1.26 1.677,1.427 0.135,0.167 10 false B 1.229,1.26 1.365,1.427 0.135,0.167 10 false C 1.094,1.26 1.229,1.427 0.135,0.167 10 false D 0.792,1.26 0.927,1.427 0.135,0.167 10 false E 2.542,1.281 2.833,1.458 0.292,0.177 10 false IK1 2.313,0.26 4.667,0.604 2.354,0.344 10 false Front view of wire harness connector: (to Front Door Wire LH) 4.813,0.26 7.146,0.604 2.333,0.344 10 false Rear view of wire harness connector: (to Rear Airbag Sensor LH) 3.656,1.646 4.552,1.833 0.896,0.188 10 false Connector C 4.948,1.281 5.177,1.458 0.229,0.177 10 false K7 6.104,1.646 7,1.833 0.896,0.188 10 false Connector B 3.813,2.094 4.229,2.25 0.417,0.156 10 false BCL- 4.813,2.135 5.229,2.292 0.417,0.156 10 false BCL- 2.396,2.208 2.813,2.365 0.417,0.156 10 false BCL+ 6.177,2.208 6.594,2.365 0.417,0.156 10 false BCL+ 3.479,2.51 4.323,2.688 0.844,0.177 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K7-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - Body ground Always 1 MΩ or higher
K7-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE