Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A10  Front Radar Sensor  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash control operation signals.

When the driving support ECU assembly receives information that there is a malfunction in the millimeter wave radar sensor assembly, DTC C1A10 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A10 When the engine switch is on (IG), the driving support ECU assembly receives information that there is a malfunction in the millimeter wave radar sensor assembly for approximately 0.2 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. When a new millimeter wave radar sensor assembly is installed to the vehicle, it receives vehicle information from the driving support ECU assembly and stores it. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly and millimeter wave radar sensor assembly will not match and a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.




PROCEDURE

1.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A10 is output A
DTC C1A10 is not output B


A

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).



NEXT

3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Adjust the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-crash 2 / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A10 is not output A
DTC C1A10 is output B


A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY