Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash control operation signals.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the driving support ECU assembly detects this, and stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A11 When the engine switch is on (IG), misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.
·

No. 1 millimeter wave radar sensor bracket

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


C1A14 When the vehicle is being driven at a speed of 10 km/h (6 mph) or more, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.


·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. When a new millimeter wave radar sensor assembly is installed to the vehicle, it receives vehicle information from the driving support ECU assembly and stores it. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly and millimeter wave radar sensor assembly will not match and a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



PROCEDURE

1.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



Result
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C


A

2.CHECK VEHICLE CONDITION

B

6.PERFORM MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS ADJUSTMENT)

C

8.CLEAR DTC
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result
Result Proceed to
Vehicle is not overloaded or has not been towed. A
Vehicle is overloaded or has been towed. B


A

3.CHECK WHEEL ALIGNMENT

B

9.PERFORM MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS ADJUSTMENT)
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe) (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B


A

4.ADJUST WHEEL ALIGNMENT

B

5.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).



NEXT

5.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

Result
Result Proceed to
Bracket is not deformed A
No. 1 millimeter wave radar sensor bracket is deformed B
The other than No. 1 millimeter wave radar sensor bracket is deformed C



A

6.PERFORM MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS ADJUSTMENT)

B

REPLACE NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET

C

REPLACE DRIVING SUPPORT ECU ASSEMBLY

6.PERFORM MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS ADJUSTMENT)
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

7.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
7.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



g.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

HINT:

After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the driving support ECU assembly.



Result
Result Proceed to
DTC C1A11 and C1A14 are not output A
DTC C1A11 or C1A14 is output B


A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY [BEAM AXIS ADJUSTMENT] WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

8.CLEAR DTC
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.

HINT:

If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.





NEXT

END

9.PERFORM MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS ADJUSTMENT)
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).




NEXT

END