Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A46  Yaw Rate Sensor  


DESCRIPTION

The driving support ECU assembly receives yaw rate sensor signals from the airbag sensor assembly (yaw rate and acceleration sensor) and master cylinder solenoid (skid control ECU) via CAN communication. If the driving support ECU assembly receives yaw rate sensor malfunction signals from the airbag sensor assembly (yaw rate and acceleration sensor) or master cylinder solenoid (skid control ECU), DTC C1A46 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A46 While the vehicle speed is 5 km/h (3 mph) or more, the driving support ECU assembly receives yaw rate sensor malfunction signals from airbag sensor assembly (yaw rate and acceleration sensor) or master cylinder solenoid (skid control ECU) for approximately 10 seconds.
·

Vehicle stability control system

·

Master cylinder solenoid (skid control ECU)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.


·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK DTC OUTPUT (VSC SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Check for vehicle stability control system DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B

HINT:

If the airbag sensor assembly (yaw rate and acceleration sensor) is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.




A

2.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Drive the vehicle at a speed of 5 km/h (3 mph) or more.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A46 is output A
DTC C1A46 is not output B


A

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Drive the vehicle at a speed of 5 km/h (3 mph) or more.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output (for LHD) B
DTC C1A46 is output (for RHD) C


A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)