Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The driving support ECU assembly receives steering angle information from the steering sensor. If the driving support ECU assembly detects a steering sensor malfunction, DTC C1A47 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A47 While the vehicle speed is 50 km/h (31 mph) or more, the driving support ECU assembly receives a steering sensor malfunction signal continuously for 1 second or more.
·

Vehicle stability control system

·

Driving support ECU assembly

·

Master cylinder solenoid (skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.


·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

PROCEDURE

1.CHECK DTC OUTPUT (VSC SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Result
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B

HINT:

If the steering sensor is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.



A

2.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Drive the vehicle at a speed of 50 km/h (31 mph) or more.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A47 is output A
DTC C1A47 is not output B


A

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
4.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Drive the vehicle at a speed of 50 km/h (31 mph) or more.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output (for LHD) B
DTC C1A47 is output (for RHD) C


A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)