Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Circuit  


DESCRIPTION

This circuit supplies power to the driving support ECU assembly when the engine switch is on (IG).

WIRING DIAGRAM

E259149E89
1.073,0.51 2.646,1.031 1.573,0.521 10 false from IG NO. 4 Relay 5.979,0.51 6.385,0.75 0.406,0.24 10 false B 5.708,1.323 5.958,1.49 0.25,0.167 10 false 28 5.979,1.406 6.313,1.552 0.333,0.146 10 false GND 5.708,0.427 6.01,0.76 0.302,0.333 10 false 7 5.094,2.073 7.042,2.292 1.948,0.219 10 false Driving Support ECU Assembly 5.104,1.917 5.469,2.281 0.365,0.365 10 false E164 3.615,0.667 4.615,0.948 1,0.281 10 false ECU-IG NO. 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Check the customer problem analysis and symptom (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>PROBLEM SYMPTOMS TABLE).



NEXT

2.INSPECT BATTERY
2.INSPECT BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V



b.

Using the parts location and system diagram, check the system for blown-out fuses, open or short circuits in the wire harness(es) and connectors that are not properly connected by performing a visual check.

HINT:

If the voltage is 11 V or less, replace or recharge the battery before proceeding to the next step.




NEXT

3.CHECK HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
NOTICE:

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.


a.
U166510E02
2.49,1.281 2.49,1.917 2.49,1.917 2.333,1.917 true 1.229,0.979 1.24,0.344 1.24,0.344 1.083,0.344 true 0.104,0.094 0.427,0.323 0.323,0.229 10 false *a 1.604,0.208 1.979,0.396 0.375,0.188 10 false E164 1.885,1.823 2.469,1.969 0.583,0.146 10 false GND 0.917,0.24 1.5,0.385 0.583,0.146 10 false B

Disconnect the driving support ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, make sure to clear the DTCs using the GTS once the inspection has been completed.


Standard Voltage:
Tester Connection Condition Specified Condition
E164-7 (B) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E164-28 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to driving support ECU assembly)


OK

4.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.


Result
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output (for LHD (w/ Central Gateway ECU)) B
CAN communication system DTCs are output (for RHD (w/ Central Gateway ECU)) C



A

5.CHECK DTC OUTPUT

B

C

5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.




f.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs. (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).


Result
Result Proceed to
DTCs are not output A
DTCs are output B


A

6.DATA LIST / ACTIVE TEST

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

6.DATA LIST / ACTIVE TEST

NEXT

7.VEHICLE CONTROL HISTORY
7.VEHICLE CONTROL HISTORY
a.

Check whether the vehicle control history (PCS operation history) matches the customer analysis (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>VEHICLE CONTROL HISTORY).

Result
Result Proceed to
Vehicle control history matches the customer analysis A
Vehicle control history does not match customer analysis or there is no vehicle control history B



A

END

B

USE SIMULATION METHOD TO CHECK