When the ignition switch ON, the center airbag sensor assembly*1 (main body ECU [cowl side junction block LH]*2) transmits front seat inner belt state signals to the combination meter assembly through the CAN. If the driver seat belt is not fastened, the combination meter assembly blinks the driver side seat belt warning light. If the seat belt is fastened, the warning light goes off.
*1: w/ Airbag System
*2: w/o Airbag System
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Airbag System | A |
| w/o Airbag System | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| CAN system DTC is output (for LHD) | B |
| CAN system DTC is output (for RHD) | C |
| Airbag system DTC is output | D |
A
B
C
D
Check the Data List for proper functioning of the driver side seat belt buckle switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Driver Buckle SW | Driver side seat belt / Set, Unset or NG | Set: Driver side seat belt is fastened
Unset: Driver side seat belt is unfastened |
NG: Data is not determined |
| Result | Proceed to |
|---|---|
| Set or Unset is displayed on the tester screen according to the driver side seat belt condition | A |
| Set or Unset is not displayed normally on the tester screen according to the driver side seat belt condition | B |
| NG is displayed on the tester screen | C |
A
B
C
Operate the intelligent tester according to the display and select Active Test.
| Item | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Driver side seat belt warning light | ON/OFF | Confirm that the vehicle is stopped and the engine is idling. |
Driver side seat belt warning light condition can be switched by Active Test.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Multi-information Display) | B |
| NG (w/o Multi-information Display) | C |
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
C
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
Temporarily replace the center airbag sensor assembly with a new one (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).
NEXT
Check the driver side seat belt warning light function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK).
Driver side seat belt warning light operates normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Multi-information Display) | B |
| NG (w/o Multi-information Display) | C |
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
C
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| CAN system DTC is output (for LHD) | B |
| CAN system DTC is output (for RHD) | C |
A
B
C
Check the Data List for proper functioning of the driver side seat belt buckle switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D Seat Buckle SW | Driver side seat belt / ON or OFF | ON: Driver side seat belt is fastened
OFF: Driver side seat belt is unfastened |
- |
The display is as specified in the normal condition column.
OK
NG
Operate the intelligent tester according to the steps on the display and select Active Test.
| Item | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Driver side seat belt warning light | ON/OFF | Confirm that the vehicle is stopped and the engine is idling. |
Driver side seat belt warning light condition can be switched by Active Test.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
Remove the front seat inner belt assembly (for Driver Side) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Bench Seat Type)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 12 - 9 | Seat belt unfastened (buckle switch is off) | Below 1 Ω |
| Seat belt fastened (buckle switch is on) | 10 kΩ or higher |
OK
NG
Disconnect the K43*1 or L49*2 front seat inner belt assembly (for Driver Side) connector.
*1: for LHD
*2: for RHD
Disconnect the E1 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K43-12 - E1-7 (DBKL) | Always | Below 1 Ω |
| K43-12 or E1-7 (DBKL) - Body ground | Always | 10 kΩ or higher |
| K43-9 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L49-12 - E1-7 (DBKL) | Always | Below 1 Ω |
| L49-12 or E1-7 (DBKL) - Body ground | Always | 10 kΩ or higher |
| L49-9 - Body ground | Always | Below 1 Ω |
OK
NG