Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY
RM2660E _58 Vehicle Interior _052846 SEAT BELT _0255657 REAR NO. 1 SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR NO. 1 SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 73034 1.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

U155834

a.

Align the anchor plate positioning hole with the claw, and install the anchor plate with the 2 bolts.

HINT:

First install the upper bolt, and then install the lower bolt.


Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73370C 2.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

B443903E01
1.104,1.115 1.51,1.115 1.51,1.115 1.969,1.594 false 1.583,1.531 1.24,1.115 false 0.99,1.021 1.167,1.219 0.177,0.198 10 false a 2.531,0.052 2.688,0.25 0.156,0.198 10 true A 1.188,1.885 1.344,2.083 0.156,0.198 10 true B

NOTICE:

w/ Pretensioner:

When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


a.

Align the claws with the seat belt positioning holes and install the retractor of the seat belt as shown in the illustration.


b.

Install the seat belt with the 2 bolts.

HINT:

First install bolt A, and then install bolt B.


Torque:
for bolt A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
for bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B180643

w/ Pretensioner:

Connect the pretensioner connector as shown in the illustration.


d.
B184510

Install the seat belt shoulder anchor with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62639 3.INSTALL REAR FRONT QUARTER TRIM PANEL ASSEMBLY LH

Hide 62520P 4.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644

HINT:

When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.

w/o Tonneau Cover:

i.

w/o Rear Air Conditioning System:

Connect the rear seat lock control lever cable.


ii.

w/ Rear Air Conditioning System:

Connect the thermistor connector and rear seat lock control lever cable.


iii.

Attach the 18 clips and 2 claws to install the quarter trim panel.


iv.

Install the clip and bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

B186889



b.

w/ Tonneau Cover:

i.

Attach the 18 clips and 2 claws to install the quarter trim panel.


ii.

Install the screw and clip.

B186437



c.
U155782E04
1.958,1.083 2.646,1.083 2.646,1.083 2.646,1.646 true 2.063,1.677 3.271,2.115 1.208,0.438 10 true Protruding Part

w/ Rear No. 2 Seat, for LH side:

i.

Install the rear No. 2 seat belt anchor LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.




d.
B181693

w/ Rear No. 2 Seat, for RH side:

i.

Install the rear No. 2 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.
B181692

Attach the 3 claws to install the cover.



e.
B181689

Install the rear No. 1 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.
B181687

Attach the 3 claws to install the cover.


Hide 64937A 6.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

Hide 10.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 13.CHECK SRS WARNING LIGHT