Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1417/17  Rear Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 2 cooler thermistor is installed on the evaporator in the rear air conditioning unit to detect the cooled air temperature that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 2 cooler thermistor changes in accordance with the cooled air temperature that has passed through the rear evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 2 cooler thermistor and reads voltage changes as the resistance of the No. 2 cooler thermistor changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1417/17 An open or short in the No. 2 cooler thermistor circuit.
·

Harness or connector between No. 2 air conditioning harness assembly and air conditioning amplifier assembly

·

No. 2 air conditioning harness assembly (No. 2 cooler thermistor)

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E160576E04
3.126,0.605 3.235,0.759 0.110,0.154 10 - 3.116,1.158 3.221,1.312 0.106,0.154 10 + 3.341,0.584 3.451,0.738 0.110,0.154 10 7 3.324,1.145 3.429,1.299 0.106,0.154 10 8 5.298,0.587 5.473,0.741 0.175,0.154 10 1 5.419,1.645 5.696,1.799 0.277,0.154 10 E35 5.595,1.227 6.001,1.381 0.405,0.154 10 TEC 5.6,0.678 5.866,0.832 0.267,0.154 10 SG 5.264,1.146 5.450,1.300 0.185,0.154 10 17 0.507,1.558 2.065,1.763 1.559,0.205 10 No. 2 Cooler Thermistor 0.476,2.196 0.748,2.352 0.272,0.156 10 K19 0.476,2.355 3.231,2.511 2.756,0.156 10 No. 2 Air Conditioning Harness Assembly 5.418,1.817 7.008,2.228 1.590,0.411 10 Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (NO. 2 COOLER THERMISTOR)
a.

Use the Data List to check if the No. 2 cooler thermistor is functioning properly.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sens (Rear) No. 2 cooler thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual rear evaporator temperature displayed Open in the circuit: -29.7°C (-21.46°F).
Short in the circuit: 59.55°C (139.19°F).

OK:

The display is as specified in the normal condition.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.INSPECT NO. 2 COOLER THERMISTOR
2.INSPECT NO. 2 COOLER THERMISTOR
E349524E01
2.188,0.74 2.25,0.74 2.25,0.74 2.292,1.229 false 2.531,0.74 2.458,0.74 2.458,0.74 2.396,1.208 false 0.74,1.719 0.615,1.719 0.615,1.719 0.615,2.75 false 2.052,0.656 2.208,0.854 0.156,0.198 10 false + 2.615,0.646 2.771,0.844 0.156,0.198 10 false - 0.813,1.646 1.646,2.021 0.833,0.375 10 false No. 2 Cooler Thermistor 0.333,3.104 2.917,3.333 2.583,0.229 10 false No. 2 Air Conditioning Harness Assembly 4.281,0.354 5.365,0.573 1.083,0.219 10 false Resistance (kΩ) 4.292,0.729 4.625,0.938 0.333,0.208 10 false 10.0 4.365,0.906 4.698,1.115 0.333,0.208 10 false 9.0 4.365,1.094 4.698,1.302 0.333,0.208 10 false 8.0 4.365,1.26 4.698,1.469 0.333,0.208 10 false 7.0 4.365,1.427 4.698,1.635 0.333,0.208 10 false 6.0 4.365,1.604 4.698,1.813 0.333,0.208 10 false 5.0 4.365,1.792 4.708,2.135 0.344,0.344 10 false 4.0 4.365,1.979 4.698,2.188 0.333,0.208 10 false 3.0 4.365,2.146 4.698,2.354 0.333,0.208 10 false 2.0 4.365,2.333 4.698,2.542 0.333,0.208 10 false 1.0 4.365,2.51 4.698,2.719 0.333,0.208 10 false 0.0 4.604,2.604 4.938,2.813 0.333,0.208 10 false -10 4.604,2.792 4.938,3 0.333,0.208 10 false (14) 5.135,2.604 5.469,2.813 0.333,0.208 10 false 0 5.677,2.604 6.01,2.813 0.333,0.208 10 false 10 6.271,2.615 6.604,2.823 0.333,0.208 10 false 20 6.802,2.615 7.135,2.823 0.333,0.208 10 false 30 5.063,2.781 5.396,2.99 0.333,0.208 10 false (32) 5.646,2.781 5.979,2.99 0.333,0.208 10 false (50) 6.771,2.771 7.104,2.979 0.333,0.208 10 false (86) 6.229,2.771 6.563,2.979 0.333,0.208 10 false (68) 5.042,3.188 6.125,3.406 1.083,0.219 10 false Temperature °C 5.813,3.396 6.156,3.635 0.344,0.24 10 false (°F)

a.

Remove the No. 2 air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (-) - 8 (+) -10°C (14°F) 7.40 to 9.20 kΩ
-5°C (23°F) 5.65 to 7.00 kΩ
0°C (32°F) 4.35 to 5.40 kΩ
5°C (41°F) 3.40 to 4.20 kΩ
10°C (50°F) 2.68 to 3.30 kΩ
15°C (59°F) 2.10 to 2.60 kΩ
20°C (68°F) 1.66 to 2.10 kΩ
25°C (77°F) 1.32 to 1.66 kΩ
30°C (86°F) 1.05 to 1.35 kΩ


NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).




OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
E349525E01
0.688,1.563 1.052,1.823 0.365,0.26 5.948,1.031 6.313,1.292 0.365,0.26 1.875,1.979 2.344,1.448 false 2.021,2 2.5,1.719 false 5.583,3.292 5.729,3.292 5.729,3.292 6.448,2.458 false 6.5,3.365 6.573,2.688 false 0.198,0.135 2.469,0.688 2.271,0.552 10 false Front view of wire harness connector: (to No. 2 Air Conditioning Harness Assembly) 3.917,0.146 6.323,0.531 2.406,0.385 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 0.75,1.615 1.052,1.844 0.302,0.229 10 false K19 6.01,1.073 6.281,1.25 0.271,0.177 10 true E35 2.583,1.625 2.781,1.854 0.198,0.229 10 false + 2.396,1.292 2.594,1.521 0.198,0.229 10 false - 5.292,3.208 5.583,3.448 0.292,0.24 10 false SG 6.365,3.417 6.729,3.625 0.365,0.208 10 false TEC

a.

Disconnect the K19 No. 2 air conditioning harness connector.


b.

Disconnect the E35 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K19-8 (+) - E35-17 (TEC) Always Below 1 Ω
K19-7 (-) - E35-1 (SG) Always Below 1 Ω
E35-17 (TEC) - Body ground Always 10 kΩ or higher
E35-1 (SG) - Body ground Always 10 kΩ or higher




OK

4.CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (OPERATION)
a.

Replace the No. 2 air conditioning harness assembly with a normal one and check that the condition returns to normal (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).



NEXT

5.CHECK FOR DTC