Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1423/23  Pressure Sensor Circuit  


DESCRIPTION

This DTC is output when refrigerant pressure is extremely low (-0.4566 MPaG (-4.6 kgf/cm2, -66 psi) or less) or extremely high (3.2943 MPaG (33.6 kgf/cm2, 477 psi) or more). The air conditioner pressure sensor, which is installed on the pipe of the high pressure side to detect refrigerant pressure, outputs the refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts the signal to pressure according to the sensor characteristics to control the compressor.

HINT:

Be sure to check the refrigerant volume first when this DTC is output because this DTC can also be output if there is no refrigerant in the cycle.


DTC Code DTC Detection Condition Trouble Area
B1423/23
·

An open or short in the air conditioner pressure sensor circuit

·

Refrigerant pressure on the high pressure side is extremely low (-0.4566 MPaG (-4.6 kgf/cm2, -66 psi) or less) or extremely high (3.2943 MPaG (33.6 kgf/cm2, 477 psi) or more)


·

Air conditioner pressure sensor

·

Harness or connector

·

Cooler expansion valve (blocked, stuck)

·

Cooler condenser assembly (blocked, deterioration of cooling capacity due to dirt)

·

Cooler dryer (moisture in the refrigerant cycle cannot be absorbed)

·

Condenser fan (condenser cannot be cooled down)

·

Air conditioning system (leaks, blocked)

·

Refrigerant pipe line

·

Air conditioning amplifier assembly



WIRING DIAGRAM

w/ Rear Heater:


E316642E11
4.479,2.865 4.938,3.063 0.458,0.198 10 false E35 4.479,3.031 6.927,3.365 2.448,0.333 10 false Air Conditioning Amplifier Assembly 4.563,1.094 5.01,1.281 0.448,0.188 10 false S5-3 4.573,1.573 5.021,1.76 0.448,0.188 10 false PRE 4.563,2.031 5.01,2.219 0.448,0.188 10 false SG-2 4.24,1.094 4.688,1.281 0.448,0.188 10 false 13 4.313,1.573 4.76,1.76 0.448,0.188 10 false 9 4.24,2.042 4.688,2.229 0.448,0.188 10 false 32 1.99,1.083 2.438,1.271 0.448,0.188 10 false 3 2,1.573 2.448,1.76 0.448,0.188 10 false 2 2,2.042 2.448,2.229 0.448,0.188 10 false 1 1.656,1.563 2.104,1.75 0.448,0.188 10 false PR 1.74,1.083 2.188,1.271 0.448,0.188 10 false + 1.75,2.042 2.198,2.229 0.448,0.188 10 false - 0.323,2.563 0.781,2.76 0.458,0.198 10 false A13 0.323,2.729 2.771,3.063 2.448,0.333 10 false Air Conditioner Pressure Sensor 5.531,0.938 5.979,1.125 0.448,0.188 10 false 5 V 5.99,1.688 6.438,1.875 0.448,0.188 10 false AD


w/o Rear Heater:


E316642E12
4.479,2.865 4.938,3.063 0.458,0.198 10 false E81 4.479,3.031 6.927,3.365 2.448,0.333 10 false Air Conditioning Amplifier Assembly 4.563,1.094 5.01,1.281 0.448,0.188 10 false S5-3 4.573,1.573 5.021,1.76 0.448,0.188 10 false PRE 4.563,2.031 5.01,2.219 0.448,0.188 10 false SG-2 4.24,1.094 4.688,1.281 0.448,0.188 10 false 30 4.313,1.573 4.76,1.76 0.448,0.188 10 false 9 4.24,2.031 4.688,2.219 0.448,0.188 10 false 13 1.99,1.083 2.438,1.271 0.448,0.188 10 false 3 2,1.573 2.448,1.76 0.448,0.188 10 false 2 2,2.042 2.448,2.229 0.448,0.188 10 false 1 1.656,1.563 2.104,1.75 0.448,0.188 10 false PR 1.74,1.083 2.188,1.271 0.448,0.188 10 false + 1.75,2.042 2.198,2.229 0.448,0.188 10 false - 0.385,2.563 0.844,2.76 0.458,0.198 10 false A13 0.375,2.708 2.823,3.042 2.448,0.333 10 false Air Conditioner Pressure Sensor 5.531,0.938 5.979,1.125 0.448,0.188 10 false 5 V 5.99,1.688 6.438,1.875 0.448,0.188 10 false AD


CAUTION / NOTICE / HINT

HINT:

If DTC B1423/23 and B14B8 are output at the same time, troubleshoot for DTC B14B8 first.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U156759E04
2.042,1.229 2.25,1.708 2.25,1.708 2.542,1.708 false 0.094,0.073 0.365,0.281 0.271,0.208 10 false *a 2.604,1.615 2.875,1.823 0.271,0.208 10 false + 0.583,1.052 0.854,1.26 0.271,0.208 10 false A13

Disconnect the air conditioner pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-3 (+) - Body ground Ignition switch ON 4.4 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
U156760E03
1.406,1.25 1.198,1.729 1.198,1.729 0.906,1.729 false 0.073,0.073 0.344,0.281 0.271,0.208 10 false *a 0.76,1.604 1.031,1.813 0.271,0.208 10 false - 0.573,1.052 0.844,1.26 0.271,0.208 10 false A13

Disconnect the air conditioner pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (-) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)



OK

3.INSPECT AIR CONDITIONER PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT)

NG

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
3.INSPECT AIR CONDITIONER PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT)
a.
U156621E01
0.048,0.008 2.366,0.359 2.318,0.350 10 *a 2.373,0.885 2.649,1.041 0.276,0.156 10 E35 1.512,2.933 1.868,3.101 0.357,0.168 10 PRE 2.779,2.058 2.282,3.011 2.282,3.011 1.951,3.011 false

w/ Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E35-9 (PRE) - Body ground
·

Ignition switch ON

·

A/C switch off


0.7 to 4.8 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



b.
U166615E01
0.032,0.048 0.341,0.233 0.309,0.186 10 *a 2.502,0.369 2.811,0.555 0.309,0.186 10 PRE 1.77,0.343 2.079,0.528 0.309,0.186 10 E81 2.002,1.027 2.282,0.457 2.282,0.457 2.475,0.457 false

w/o Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-9 (PRE) - Body ground
·

Ignition switch ON

·

A/C switch off


0.7 to 4.8 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



HINT:

If the measured voltage is not within the normal range, there may be a malfunction in the air conditioning amplifier assembly, air conditioner pressure sensor, or wire harness. It is also possible that the amount of refrigerant may not be appropriate.



OK

4.INSPECT AIR CONDITIONER PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT)

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
4.INSPECT AIR CONDITIONER PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT)
a.

Measure the voltage when the following conditions are satisfied.

Item Condition
Engine Speed 1500 rpm
Vehicle Doors Fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C Switch ON
R/F Switch RECIRCULATION
Interior Temperature 25 to 35°C (77 to 95°F)

NOTICE:
·

If refrigerant pressure on the high pressure side becomes extremely high during the inspection (if the voltage exceeds 4.8 V), the fail-safe function stops compressor operation. Therefore, measure the voltage before the fail-safe operation.

·

It is necessary to measure the voltage for a certain amount of time (approximately 10 minutes) because the problem symptom may recur after a while.



HINT:

When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the ambient temperature and the evaporator temperature sensor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.


i.

w/ Rear Heater:

1.
U156621E01
0.048,0.008 2.366,0.359 2.318,0.350 10 *a 2.373,0.885 2.649,1.041 0.276,0.156 10 E35 1.512,2.933 1.868,3.101 0.357,0.168 10 PRE 2.779,2.058 2.282,3.011 2.282,3.011 1.951,3.011 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E35-9 (PRE) - Body ground
·

Ignition switch ON

·

A/C switch on


0.7 to 4.8 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



ii.

w/o Rear Heater:

1.
U166615E01
0.032,0.048 0.341,0.233 0.309,0.186 10 *a 2.502,0.369 2.811,0.555 0.309,0.186 10 PRE 1.77,0.343 2.079,0.528 0.309,0.186 10 E81 2.002,1.027 2.282,0.457 2.282,0.457 2.475,0.457 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B81-9 (PRE) - Body ground
·

Ignition switch ON

·

A/C switch on


0.7 to 4.8 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

13.INSPECT CONDENSER FAN
5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

w/ Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E35 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (+) - E35-13 (S5-3) Always Below 1 Ω
A13-3 (+) or E35-13 (S5-3) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E81 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (+) - E81-30 (S5-3) Always Below 1 Ω
A13-3 (+) or E81-30 (S5-3) - Body ground Always 10 kΩ or higher





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

w/ Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E35 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (-) - E35-32 (SG-2) Always Below 1 Ω
A13-1 (-) or E35-32 (SG-2) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E81 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (-) - E81-13 (SG-2) Always Below 1 Ω
A13-1 (-) or E81-13 (SG-2)- Body ground Always 10 kΩ or higher





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

w/ Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E35 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (PR) - E35-9 (PRE) Always Below 1 Ω
A13-2 (PR) or E35-9 (PRE) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the A13 air conditioner pressure sensor connector.


ii.

Disconnect the E81 air conditioning amplifier assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (PR) - E81-9 (PRE) Always Below 1 Ω
A13-2 (PR) or E81-9 (PRE) - Body ground Always 10 kΩ or higher





OK

8.INSPECT FOR AIR CONDITIONING SYSTEM LEAK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FOR AIR CONDITIONING SYSTEM LEAK
a.

Install the manifold gauge set.


b.

Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.


c.

Evacuate the air conditioning system and check that vacuum can be maintained in it.

OK:

Vacuum can be maintained in the air conditioning system.


HINT:

If vacuum cannot be maintained in the air conditioning system, refrigerant may be leaking from it. In this case, it is necessary to repair or replace the leaking part of the air conditioning system.




OK

9.CHARGE REFRIGERANT

NG

12.REPAIR AIR CONDITIONING SYSTEM LEAK
9.CHARGE REFRIGERANT
a.

Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).



NEXT

10.RECHECK FOR DTC
10.RECHECK FOR DTC
a.

Recheck for DTCs when the following conditions are satisfied.

Item Condition
Engine Speed 1500 rpm
Vehicle Doors Fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C Switch ON
R/F Switch RECIRCULATION
Interior Temperature 25 to 35°C (77 to 95°F)

NOTICE:

If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. Therefore, it is necessary to measure the voltage for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning system operates for a while.


HINT:

When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the ambient temperature sensor and the evaporator temperature sensor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.


OK:

DTC B1423 is not output.


NOTICE:

If the DTC was output due to an insufficient or excessive amount of refrigerant, the problem may have been solved after performing the previous step. However, the root cause of insufficient refrigerant may be refrigerant leaks. The root cause of excessive refrigerant may be adding refrigerant when the level was insufficient. Therefore, identify and repair the area where refrigerant leaks as necessary.




OK

END

NG

11.CHECK AIR CONDITIONER PRESSURE SENSOR
11.CHECK AIR CONDITIONER PRESSURE SENSOR
a.

Install the manifold gauge set.

E349665E02
2.5,1.302 2.865,1.552 0.365,0.25 2.521,2.344 2.885,2.594 0.365,0.25 1.896,1.75 1.823,2.094 1.823,2.094 1.719,2.094 false 2.146,1.594 2.26,1.01 2.26,1.01 2.396,1.021 false 1.417,2.583 1.542,3.094 1.542,3.094 1.646,3.094 false 1.156,2.594 1.094,3.094 1.094,3.094 0.948,3.094 false 0.302,0.313 0.646,0.604 0.344,0.292 10 false *a 4.781,0.375 5.604,0.667 0.823,0.292 10 false (V)Voltage 2.552,1.333 2.896,1.531 0.344,0.198 10 false E35 1.333,2 1.781,2.208 0.448,0.208 10 false SG-2 2.469,0.927 2.917,1.135 0.448,0.208 10 false PRE 2.896,1.354 3.146,1.552 0.25,0.198 10 false *A 2.583,2.385 2.927,2.583 0.344,0.198 10 false E81 2.938,2.385 3.188,2.583 0.25,0.198 10 false *B 1.76,3.01 2.208,3.219 0.448,0.208 10 false PRE 0.542,3.031 0.99,3.24 0.448,0.208 10 false SG-2 4.5,1.802 4.771,1.979 0.271,0.177 10 false 0.5 4.354,0.688 4.75,0.865 0.396,0.177 10 false 4.834 4.344,1.583 4.74,1.76 0.396,0.177 10 false 1.030 4.49,0.542 4.76,0.719 0.271,0.177 10 false 4.9 4.5,1.948 4.771,2.125 0.271,0.177 10 false 0.1 5.021,2.156 5.177,2.333 0.156,0.177 10 false 0 5.208,2.156 5.521,2.344 0.313,0.188 10 false 0.39 5.229,2.302 5.542,2.49 0.313,0.188 10 false (57) 5.99,2.156 6.375,2.344 0.385,0.188 10 false 3.187 6.01,2.302 6.365,2.49 0.354,0.188 10 false (463) 6.625,2.146 7.01,2.333 0.385,0.188 10 false MPa 6.625,2.281 6.979,2.469 0.354,0.188 10 false (psi) 5.188,2.521 6.479,2.719 1.292,0.198 10 false Refrigerant Pressure


b.

Reconnect the A13 air conditioner pressure sensor connector.


c.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


d.

Turn the Ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Rear Heater:
Tester Connection Condition Specified Condition
E35-9 (PRE) - E35-32 (SG-2) Refrigerant pressure:
Normal pressure (less than 3.0732 MPa [31.4 kgf/cm2, 445 psi] and more than 0.1762 MPa [1.8 kgf/cm2, 25 psi])
1.0 to 4.8 V
Refrigerant pressure:
Abnormal (less than 0.1762 MPa [1.8 kgf/cm2, 25 psi])
Below 1 V
Refrigerant pressure:
Abnormal (more than 3.0732 MPa [31.4 kgf/cm2, 445 psi])
4.8 V or higher

w/o Rear Heater:
Tester Connection Condition Specified Condition
E81-9 (PRE) - E81-13 (SG-2) Refrigerant pressure:
Normal pressure (less than 3.0732 MPa [31.4 kgf/cm2, 445 psi] and more than 0.1762 MPa [1.8 kgf/cm2, 25 psi])
1.0 to 4.8 V
Refrigerant pressure:
Abnormal (less than 0.1762 MPa [1.8 kgf/cm2, 25 psi])
Below 1 V
Refrigerant pressure:
Abnormal (more than 3.0732 MPa [31.4 kgf/cm2, 445 psi])
4.8 V or higher


Text in Illustration
*A w/ Rear Heater
*B w/o Rear Heater
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

12.REPAIR AIR CONDITIONING SYSTEM LEAK
a.

Identify the area where refrigerant leaks (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>ON-VEHICLE INSPECTION).


b.

Repair the identified area of the air conditioning system.


c.

Evacuate the air conditioning system.



NEXT

13.INSPECT CONDENSER FAN
NOTICE:

For vehicles without an condenser fan, go to "CHARGE REFRIGERANT".


a.

Inspect that the condenser fan operates normally (See page Vehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>INSPECTION).



OK

14.CHARGE REFRIGERANT

NG

14.CHARGE REFRIGERANT
a.

Use a refrigerant recovery unit to recover refrigerant.


b.

Evacuate the air conditioning system.


c.

Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).

HINT:

If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC.




NEXT

15.RECHECK FOR DTC
15.RECHECK FOR DTC
a.

Recheck for DTCs when the following conditions are satisfied.

Item Condition
Engine Speed 1500 rpm
Vehicle Doors Fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C Switch ON
R/F Switch RECIRCULATION
Interior Temperature 25 to 35°C (77 to 95°F)

NOTICE:

If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. Therefore, it is necessary to measure the voltage for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning system operates for a while.


HINT:
·

When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the ambient temperature sensor and the evaporator temperature sensor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.

·

If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC. If the DTC is not output after this procedure, it indicates that the cooler dryer in the condenser is not able to absorb moisture in the refrigerant cycle. In this case, to complete the repair it is necessary to replace the cooler dryer.



OK:

DTC B1423 is not output.




OK

NG

16.REPLACE COOLER EXPANSION VALVE
16.REPLACE COOLER EXPANSION VALVE
a.

Replace the cooler expansion valve with a normal one.


HINT:

Replace the cooler expansion valve with a normal one because the cooler expansion valve is either stuck or clogged.




NEXT

17.CHARGE REFRIGERANT
17.CHARGE REFRIGERANT
a.

Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).



NEXT

18.RECHECK FOR DTC
18.RECHECK FOR DTC
a.

Recheck for DTCs when the following conditions are satisfied.

Item Condition
Engine Speed 1500 rpm
Vehicle Doors Fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C Switch ON
R/F Switch RECIRCULATION
Interior Temperature 25 to 35°C (77 to 95°F)

NOTICE:

If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. Therefore, it is necessary to measure the voltage for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning system operates for a while.


HINT:
·

When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the ambient temperature sensor and the evaporator temperature sensor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.

·

If refrigerant pressure is not normal after replacing the expansion valve with a normal one, the condenser or pipes may be clogged due to dirt, dust or other contaminants. In this case, clean or replace the condenser or pipes.



OK:

DTC B1423 is not output.




OK

END

NG

REPLACE COOLER CONDENSER ASSEMBLY