Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Magnetic Valve Circuit  


DESCRIPTION

The rear cooling unit expansion valve (rear magnetic valve) is controlled by the air conditioning amplifier assembly.

WIRING DIAGRAM

E157387E15
0.844,2.156 1.125,2.323 0.281,0.167 10 false z50 0.833,2.333 1.854,2.813 1.021,0.479 10 false Rear Cooling Unit Expansion Valve 1.75,1.115 1.917,1.281 0.167,0.167 10 false 2 1.75,1.625 1.917,1.792 0.167,0.167 10 false 1 2.125,2.292 3.688,2.677 1.563,0.385 10 false Wiring Air Conditioning Harness Sub-assembly 3.448,1.208 3.656,1.406 0.208,0.198 10 false +S 3.24,1.74 3.677,1.948 0.438,0.208 10 false RMGV 3.771,1.604 3.938,1.75 0.167,0.146 10 false 3 3.771,1.094 3.938,1.24 0.167,0.146 10 false 2 4.271,0.885 4.76,1.042 0.49,0.156 10 false A/C IG 3.563,0.271 4.917,0.49 1.354,0.219 10 false from IG1 NO. 2 Relay 5.365,1.719 5.865,1.865 0.5,0.146 10 false RMGV 5.052,1.594 5.271,1.792 0.219,0.198 10 false 19 5.167,2.698 5.469,2.865 0.302,0.167 10 false E36 5.167,2.875 6.875,3.354 1.708,0.479 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR A/C MAG VALVE)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the rear cooling unit expansion valve operates.

OK:

Rear cooling unit expansion valve operates normally.


Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Rear A/C Mag Valv Rear cooling unit expansion valve OFF or ON -



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.INSPECT FUSE (A/C IG)
2.INSPECT FUSE (A/C IG)
a.

Remove the A/C IG fuse from the cowl side junction block LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C IG fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - BATTERY)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - BATTERY)
a.
E157378E03
0.095,0.093 2.595,0.594 2.500,0.501 10 Front view of wire harness connector: (to Air Conditioning Wiring Harness Sub-assembly) 2.899,1.358 3.104,1.522 0.205,0.164 10 +S 2.327,1.998 2.853,1.455 false

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (+S) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
E350068E01
5.208,1.167 5.542,1.385 0.333,0.219 1.948,2.896 2.083,2.281 false 4.615,2.896 4.875,2.646 false 0.177,0.135 2.469,0.708 2.292,0.573 10 false Front view of wire harness connector: (to Air Conditioning Wiring Harness Sub-assembly) 3.906,0.188 6.365,0.594 2.458,0.406 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 1.75,2.938 2.365,3.135 0.615,0.198 10 false RMGV 5.26,1.198 5.542,1.365 0.281,0.167 10 true E36 4.156,2.833 4.771,3.031 0.615,0.198 10 false RMGV

a.

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Disconnect the E36 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (RMGV) - E36-19 (RMGV) Always Below 1 Ω
3 (RMGV) - Body ground Always 10 kΩ or higher
E36-19 (RMGV) - Body ground




OK

5.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)
a.

Replace the rear cooling unit expansion valve (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).

HINT:

Since the rear cooling unit expansion valve cannot be inspected while it is removed from the vehicle, replace the rear cooling unit expansion valve with a normal one and check that the condition returns to normal.


OK:

Same problem does not occur.




OK

NG

6.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (OPERATION)
6.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (OPERATION)
a.

Replace the wiring air conditioning harness sub-assembly with a normal one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

REPLACE WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY