Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Magnetic Valve Circuit  


DESCRIPTION

The rear cooling unit expansion valve is controlled by the air conditioning amplifier assembly.

WIRING DIAGRAM

E330416E04
5.229,2.063 6.813,2.438 1.583,0.375 10 false Air Conditioning Amplifier Assembly 5.24,1.917 5.75,2.094 0.51,0.177 10 false E36 5.479,1.385 5.99,1.563 0.51,0.177 10 false RMGV 5.219,1.292 5.729,1.469 0.51,0.177 10 false 19 3.542,0.76 4.51,0.927 0.969,0.167 10 false ECU-IG NO.3 4.719,0.583 6.177,0.771 1.458,0.188 10 false from IG1 NO.2 Relay 3.458,0.51 3.708,0.688 0.25,0.177 10 false 2 3.479,1.302 3.729,1.479 0.25,0.177 10 false 3 2.219,0.5 2.469,0.677 0.25,0.177 10 false 2 2.208,1.292 2.458,1.469 0.25,0.177 10 false 1 1.969,1.896 3.479,2.292 1.51,0.396 10 false Wiring Air Conditioning Harness Sub-assembly 0.604,1.74 1.729,2.125 1.125,0.385 10 false Rear Cooling Unit Expansion Valve

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR A/C MAG VALVE)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the rear cooling unit expansion valve operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Rear A/C Mag Valve Rear A/C magnetic valve ON or OFF -

OK:

Rear magnetic valve operates normally using GTS.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - BATTERY)
a.
E330396

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 - Body ground Ignition switch off Below 1 V
2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Wiring Air Conditioning Harness Sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Disconnect the E36 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - E36-19 (RMGV) Always Below 1 Ω
3 or E36-19 (RMGV) - Body ground Always 10 kΩ or higher




OK

4.CHECK REAR COOLING UNIT EXPANSION VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR COOLING UNIT EXPANSION VALVE
a.

Replace the rear cooling unit expansion valve with a new or known good one and check that the condition returns to normal. (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY)

HINT:

Since the rear cooling unit expansion valve cannot be inspected while it is removed from the vehicle, replace the rear cooling unit expansion valve with a new or known good one and check that the condition returns to normal.


OK:

Same problem does not occur.




OK

END (REAR COOLING UNIT EXPANSION VALVE WAS DEFECTIVE)

NG

5.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (OPERATION)
5.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (OPERATION)
a.

Replace the wiring air conditioning harness sub-assembly with a new or known good one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

END (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY