Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Air Conditioning Relay Circuit  


DESCRIPTION

When the No. 2 air conditioning control assembly (rear blower switch) is set to position LO or higher, the contact of the CLR RR relay is closed, current flows to the rear blower motor, and the rear blower motor operates. The rear blower motor speed can be changed by exchanging the ground and the rear blower resistor circuit with the No. 2 air conditioning control assembly (rear blower switch).

WIRING DIAGRAM

E337640E05
5.5,1.646 7.146,2.01 1.646,0.365 10 false Air Conditioning Amplifier Assembly 6.26,0.406 6.667,0.583 0.406,0.177 10 false RCRL 6.271,0.948 6.677,1.125 0.406,0.177 10 false GND 3.469,1.25 4.052,1.479 0.583,0.229 10 false CLR RR 1.427,5.146 2.823,5.448 1.396,0.302 10 false Rear Blower Resistor 5.458,4.688 6.813,5.052 1.354,0.365 10 false Rear Blower with Fan Motor Sub-assembly 1.271,1.969 3.76,2.344 2.49,0.375 10 false No. 2 Air Conditioning Control Assembly (Rear Blower Switch) 2.313,0.833 3.24,1.01 0.927,0.177 10 false A/C RR NO.1 4.396,0.99 5.323,1.167 0.927,0.177 10 false A/C RR NO.2 2.344,0.521 3.271,0.698 0.927,0.177 10 false ENG-IG NO.1 0.771,0.385 2.198,0.729 1.427,0.344 10 false from IG2 MAIN Relay 3.292,2.865 3.49,3.042 0.198,0.177 10 false LO 1.271,1.802 1.583,1.979 0.313,0.177 10 false E89 5.469,4.521 5.781,4.698 0.313,0.177 10 false z49 3.938,5.271 6.198,5.51 2.26,0.24 10 false Rear Cooling Unit Expansion Valve 0.333,3.74 1.354,4.385 1.021,0.646 10 false Wiring Air Conditioning Harness Sub-assembly 3.938,5.094 4.25,5.271 0.313,0.177 10 false z50 5.51,1.448 5.823,1.625 0.313,0.177 10 false E81 1.427,4.969 1.74,5.146 0.313,0.177 10 false z52 2.885,4.698 3.083,4.875 0.198,0.177 10 false LO 2.646,2.854 2.844,3.031 0.198,0.177 10 false HI 2.156,2.854 2.396,3.031 0.24,0.177 10 false M2 1.667,2.854 1.896,3.031 0.229,0.177 10 false M1 2.625,4.635 2.823,4.813 0.198,0.177 10 false HI 2.115,4.625 2.354,4.802 0.24,0.177 10 false M2 1.573,4.646 1.802,4.823 0.229,0.177 10 false M1 1.281,2.729 1.427,2.906 0.146,0.177 10 false E 6,0.313 6.167,0.49 0.167,0.177 10 false 18 6,0.885 6.167,1.063 0.167,0.177 10 false 14 4.99,4.302 5.146,4.479 0.156,0.177 10 false 1 3.896,4.302 4.052,4.479 0.156,0.177 10 false 1 4.052,0.292 4.208,0.469 0.156,0.177 10 false 2 1.698,4.292 1.854,4.469 0.156,0.177 10 false 2 2.26,4.292 2.417,4.469 0.156,0.177 10 false 3 4.042,0.729 4.198,0.906 0.156,0.177 10 false 3 2.813,4.281 2.969,4.458 0.156,0.177 10 false 1 1.708,3.073 1.865,3.25 0.156,0.177 10 false 3 2.25,3.063 2.406,3.24 0.156,0.177 10 false 4 3.281,0.594 3.438,0.771 0.156,0.177 10 false 5 2.771,3.063 2.927,3.24 0.156,0.177 10 false 8 3.417,3.063 3.573,3.24 0.156,0.177 10 false 5 1.083,2.625 1.24,2.802 0.156,0.177 10 false 6 3.177,4.792 3.333,4.969 0.156,0.177 10 false 4 3.281,0.896 3.438,1.073 0.156,0.177 10 false 4 5.354,4.292 5.51,4.469 0.156,0.177 10 false 2 4.396,4.292 4.552,4.469 0.156,0.177 10 false 2 3.281,0.281 3.438,0.458 0.156,0.177 10 false 1 1.292,0.698 2.094,1.021 0.802,0.323 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CLR RR RELAY
a.

Remove the CLR RR relay from the No.1 engine room relay block.




OK

2.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE CLR RR RELAY

2.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Remove the rear blower with fan motor sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>REMOVAL).


b.

Measure the rear blower with fan motor sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>INSPECTION).



OK

3.INSPECT NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (REAR BLOWER SWITCH)

NG

REPLACE REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

3.INSPECT NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (REAR BLOWER SWITCH)
a.
E162133E03
1.594,1.208 1.969,0.667 1.969,0.667 2.208,0.667 false 1.292,1.188 1.51,0.281 1.51,0.281 1.75,0.281 false 1.052,1.198 0.865,0.656 0.865,0.656 0.625,0.656 false 2.229,1.604 2.365,2.01 2.365,2.01 2.604,2.01 false 1.281,1.604 0.99,2.01 0.99,2.01 0.75,2.01 false 2.271,0.594 2.51,0.75 0.24,0.156 10 false M1 0.542,1.927 0.719,2.073 0.177,0.146 10 false HI 2.677,1.917 2.813,2.115 0.135,0.198 10 false E 0.385,0.583 0.604,0.76 0.219,0.177 10 false LO 1.823,0.188 2.094,0.375 0.271,0.188 10 false M2

Remove the No. 2 air conditioning control assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING PANEL>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
ALL - E89-6 (E) OFF 10 kΩ or higher
E89-5 (LO) - E89-6 (E) LO Below 1 Ω
E89-3 (M1) - E89-6 (E) M1 Below 1 Ω
E89-4 (M2) - E89-6 (E) M2 Below 1 Ω
E89-8 (HI) - E89-6 (E) HI Below 1 Ω




OK

4.INSPECT REAR BLOWER RESISTOR

NG

REPLACE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY

4.INSPECT REAR BLOWER RESISTOR

OK

5.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)

NG

5.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)
a.

Replace the rear cooling unit expansion valve (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/o Heater)>DISASSEMBLY).

HINT:

Since the rear cooling unit expansion valve cannot be inspected while it is removed from the vehicle, replace the rear cooling unit expansion valve with a normal one and check that the condition returns to normal.


OK:

Same problem does not occur.




OK

NG

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY)
a.

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Disconnect the z52 rear blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (M1) - z52-2 (M1) Always Below 1 Ω
5 (M2) - z52-3 (M2) Always Below 1 Ω
4 (HI) - z52-1 (HI) Always Below 1 Ω
7 (LO) - z52-4 (LO) Always Below 1 Ω
6 (M1) or z52-2 (M1) - Body ground Always 10 kΩ or higher
5 (M2) or z52-3 (M2) - Body ground Always 10 kΩ or higher
4 (HI) or z52-1 (HI) - Body ground Always 10 kΩ or higher
7 (LO) or z52-4 (LO) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING CONTROL ASSEMBLY - WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING CONTROL ASSEMBLY - WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY)
a.

Disconnect the E89 No. 2 air conditioning control assembly connector.


b.

Disconnect the Wiring air conditioning harness sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E89-3 (M1) - 6 (M1) Always Below 1 Ω
E89-4 (M2) - 5 (M2) Always Below 1 Ω
E89-8 (HI) - 4 (HI) Always Below 1 Ω
E89-5 (LO) - 7 (LO) Always Below 1 Ω
E89-6 (E) - Body ground Always Below 1 Ω
E89-3 (M1) or 6 (M1) - Body ground Always 10 kΩ or higher
E89-4 (M2) or 5 (M2) - Body ground Always 10 kΩ or higher
E89-8 (HI) or 4 (HI) - Body ground Always 10 kΩ or higher
E89-5 (LO) or 7 (LO) - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY)
a.

Disconnect the z52 rear blower resistor connector.


b.

Disconnect the z49 rear blower with fan motor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z52-1 (HI) - z49-1 Always Below 1 Ω
z52-1 (HI) or z49-1 - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BODY GROUND AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BODY GROUND AND BATTERY)
a.
U166009E02
0.854,1.396 1.156,1.583 0.302,0.188 10 false z49 0.094,0.094 0.448,0.323 0.354,0.229 10 false *a

Disconnect the rear blower with fan motor sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z49-2 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z49-2 - Body ground Ignition switch ON
Heater control (blower switch) HI
11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Rear Blower with Fan Motor Sub-assembly)


OK

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166421E02
0.552,0.531 0.823,0.531 0.823,0.531 0.969,1.26 false 3.01,1.708 2.729,1.708 2.729,1.708 2.656,1.438 false 1.583,0.281 2.01,0.531 0.427,0.25 10 false E81 0.094,0.052 0.521,0.302 0.427,0.25 10 false *a 3.073,1.625 3.375,1.802 0.302,0.177 10 false +B1 0.135,0.458 0.563,0.635 0.427,0.177 10 false RCRL

Disconnect the air conditioning amplifier connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-18 (RCRL) - Body ground
·

Ignition switch ON

·

Heater control (blower switch): OFF


11 to 14 V
E81-18 (RCRL) - Body ground
·

Ignition switch ON

·

Heater control (blower switch): ON


Below 1 V



Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR