Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1449/49  Rear Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The rear mode damper servo motor sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the rear mode damper servo motor to the appropriate position, which controls the air outlet modes.

HINT:

Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code DTC Detection Condition Trouble Area
B1449/49 The rear mode damper servo motor position does not change even if the air conditioning amplifier assembly operates the rear air outlet damper servo motor.
·

Rear mode damper servo motor

·

No. 2 air conditioning harness assembly

·

Harness or connector

·

Air conditioning amplifier assembly




WIRING DIAGRAM

E334389E16
4.948,1.99 6.542,2.385 1.594,0.396 10 false Air Conditioning Amplifier Assembly 4.958,1.823 5.344,1.979 0.385,0.156 10 false E36 4.823,0.5 5.292,0.667 0.469,0.167 10 false RBUS 4.833,0.813 5.302,0.979 0.469,0.167 10 false RBBU 4.833,1.115 5.302,1.281 0.469,0.167 10 false RBUG 4.563,0.458 5.031,0.625 0.469,0.167 10 false 13 4.573,0.813 5.042,0.979 0.469,0.167 10 false 14 4.583,1.125 5.052,1.292 0.469,0.167 10 false 12 4.052,0.458 4.521,0.625 0.469,0.167 10 false 3 4.052,0.813 4.521,0.979 0.469,0.167 10 false 4 4.052,1.125 4.521,1.292 0.469,0.167 10 false 2 0.583,1.719 2.615,1.969 2.031,0.25 10 false Rear Mode Damper Servo Motor 2.938,1.813 3.396,1.958 0.458,0.146 10 false K19 0.74,2.385 2.375,2.604 1.635,0.219 10 false : LIN Communication Line 2.938,1.99 4.313,2.417 1.375,0.427 10 false No. 2 Air Conditioning Harness Assembly 3.583,0.458 4.052,0.625 0.469,0.167 10 false RBUS 3.594,0.813 4.063,0.979 0.469,0.167 10 false RBBU 3.594,1.115 4.063,1.281 0.469,0.167 10 false RBUG 5.844,0.594 6.313,0.76 0.469,0.167 10 false IC 6.396,0.76 6.667,0.969 0.271,0.208 10 false +B

PROCEDURE

1.READ VALUE USING GTS (AIR OUTLET SERVO [R], AIR OUTLET SERVO ACTUAL PLS[R])
a.

Use the Data List to check if the rear mode damper servo motor is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (R) Rear mode damper servo motor target pulse / Min.: 128, Max.: 383
·

FACE: 276 (pulse)

·

B/L: 235 (pulse)

·

FOOT: 200 (pulse)


·

Displayed between 200 and 276 pulse

·

Rear mode damper servo motor system malfunction


Air Outlet Servo Actual Pls(R) Rear mode damper servo motor actual pulse / Min.: 128, Max.: 383
·

FACE: 276 (pulse)

·

B/L: 235 (pulse)

·

FOOT: 200 (pulse)


·

Displayed between 200 and 276 pulse

·

Rear mode damper servo motor system malfunction



OK:

When the rear mode switch is turned, the actual pulse changes following the target pulse.


Result
Result Proceed to
Target pulse changes but actual pulse does not change A
Target pulse and actual pulse do not change B
Actual pulse changes following the target pulse (When troubleshooting according to the DTC) C
Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) D



A

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

5.CHECK FOR DTC

E

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K19 No. 2 air conditioning harness assembly connector.


b.

Disconnect the E36 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K19-2 (RBUG) - E36-12 (RBUG) Always Below 1 Ω
K19-3 (RBUS) - E36-13 (RBUS) Always Below 1 Ω
K19-4 (RBBU) - E36-14 (RBBU) Always Below 1 Ω
K19-2 (RBUG) or E36-12 (RBUG) - Body ground Always 10 kΩ or higher
K19-3 (RBUS) or E36-13 (RBUS) - Body ground Always 10 kΩ or higher
K19-4 (RBBU) or E36-14 (RBBU) - Body ground Always 10 kΩ or higher




OK

3.CHECK REAR MODE DAMPER SERVO MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR MODE DAMPER SERVO MOTOR
a.

Replace the rear mode damper servo motor (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.






OK

END (REAR MODE DAMPER SERVO MOTOR WAS DEFECTIVE)

NG

4.CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY
4.CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

OK

END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY