*1: for LHD
*2: for RHD
The cooler thermistor (rear room temperature sensor RH*1 or LH*2) is installed in the rear quarter trim board RH*1 or LH*2 to detect the rear room temperature and control the heater and air conditioner "auto" mode. The resistance of the rear room temperature sensor RH*1 or LH*2 changes in accordance with the cooler thermistor (rear room temperature sensor RH*1 or LH*2) seat. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier applies a voltage (5 V) to the cooler thermistor (rear room temperature sensor RH*1 or LH*2) and reads voltage changes as changes in the resistance of the cooler thermistor (rear room temperature sensor RH*1 or LH*2).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1468/68 | An open or short in the cooler thermistor (rear room temperature sensor RH*1 or LH*2) circuit. | ·
Cooler thermistor (rear room temperature sensor RH)*1 ·
Cooler thermistor (rear room temperature sensor LH)*2 ·
Harness or connector ·
Air conditioning amplifier assembly |
for LHD:
for RHD:
*1: for LHD
*2: for RHD
Use the Data List to check if the cooler thermistor (rear room temperature sensor RH*1 or LH*2) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Room Temperature Sensor (RP) | Cooler thermistor (rear room temperature sensor RH*1 or LH*2) / Min.: -6.5°C (20.3°F), Max.: 57.25°C (135.05°F) | Cooler thermistor (rear room temperature RH*1 or LH*2) displayed | Cooler thermistor (rear room temperature RH*1 or LH*2)
·
Open in the circuit: -6.5°C (20.3°F) ·
Short in the circuit: 57.25°C (135.05°F) |
The display is as specified in the normal condition.
OK
NG
Remove the cooler thermistor (rear room temperature sensor RH*1 or LH*2) (See page Vehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR(for Rear Side)>REMOVAL)
Inspect the cooler thermistor (rear room temperature sensor RH*1 or LH*2 (See page Vehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR(for Rear Side)>INSPECTION).
OK
NG
(See pageVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR(for Rear Side)>REMOVAL)
for LHD:
Disconnect the z56 cooler thermistor (rear room temperature sensor RH) connector.
Disconnect the E35 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z56-2 - E35-33 (SG) | Always | Below 1 Ω |
| z56-1 - E35-22 (TSET) | Always | Below 1 Ω |
| E35-33 (SG) - E35-22 (TSET) | Always | Below 1 Ω |
| z56-2 or E35-33 (SG) - Body ground | Always | 10 kΩ or higher |
| z56-1 or E35-22 (TSET) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the z55 cooler thermistor (rear room temperature sensor LH) connector.
Disconnect the E35 air conditioning amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z56-2 - E35-33 (SG) | Always | Below 1 Ω |
| z56-1 - E35-21 (TR) | Always | Below 1 Ω |
| E35-33 (SG) - E35-21 (TR) | Always | Below 1 Ω |
| z56-2 or E35-33 (SG) - Body ground | Always | 10 kΩ or higher |
| z56-1 or E35-21 (TR) - Body ground | Always | 10 kΩ or higher |
OK
NG