Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1429/29  Rear Air Foot Duct Sensor Circuit on Front Passenger Side  


DESCRIPTION

The air duct temperature sensor RH*1 or LH*2 (for front passenger side) detects the duct temperature and sends the appropriate signals to the air conditioning amplifier assembly.

DTC Code DTC Detection Condition Trouble Area
B1429/29 An open or short in the air duct temperature sensor RH*1 or LH*2 circuit.
·

Air duct temperature sensor RH*1

·

Air duct temperature sensor LH*2

·

Harness or connector (air duct temperature sensor RH)*1

·

Harness or connector (air duct temperature sensor LH)*2

·

Air conditioning amplifier assembly



HINT:

*1: for LHD

*2: for RHD


WIRING DIAGRAM

E156584E36
5.357,0.786 5.756,0.931 0.398,0.146 10 TR3 5.361,1.803 5.808,1.945 0.447,0.142 10 SGND 5.048,1.702 5.249,1.860 0.200,0.158 10 34 5.048,0.691 5.249,0.849 0.200,0.158 10 25 1.925,1.348 4.014,1.515 2.089,0.167 10 Air Duct Temperature Sensor LH 1.816,0.683 1.939,0.822 0.123,0.140 10 2 1.995,0.711 2.118,0.850 0.123,0.140 10 - 2.873,0.711 2.996,0.850 0.123,0.140 10 + 3.032,0.685 3.305,0.919 0.273,0.234 10 1 1.925,1.18 2.260,1.338 0.335,0.158 10 K21 4.92,2.223 5.262,2.409 0.342,0.186 10 E35 4.92,2.385 7.152,2.549 2.232,0.164 10 Air Conditioning Amplifier Assembly 0.056,0.039 1.083,0.306 1.026,0.267 12 for RHD:

E156584E37
5.357,0.786 5.756,0.931 0.398,0.146 10 TR4 5.361,1.803 5.808,1.945 0.447,0.142 10 SG-9 5.048,1.702 5.249,1.860 0.200,0.158 10 12 5.068,0.691 5.268,0.849 0.200,0.158 10 26 1.925,1.348 4.014,1.515 2.089,0.167 10 Air Duct Temperature Sensor RH 1.816,0.683 1.939,0.822 0.123,0.140 10 2 1.995,0.711 2.118,0.850 0.123,0.140 10 - 2.873,0.711 2.996,0.850 0.123,0.140 10 + 3.032,0.685 3.305,0.919 0.273,0.234 10 1 1.925,1.18 2.260,1.338 0.335,0.158 10 L12 4.92,2.223 5.262,2.409 0.342,0.186 10 E35 4.92,2.385 7.152,2.549 2.232,0.164 10 Air Conditioning Amplifier Assembly 0.056,0.039 1.083,0.306 1.026,0.267 12 for LHD:

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AIR DUCT TEMPERATURE SENSOR)
a.

Use the Data List to check if the air duct temperature sensor RH*1 or LH*2 (for front passenger side) is functioning properly.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Foot Duct Sensor (Rear P) Min.: -12.7°C (9.14°F)
Max.: 76.55°C (169.79°F)
Actual air duct temperature sensor (for passenger side) displayed Open in the circuit: -12.7°C (9.14°F)
Short in the circuit: 76.55°C (169.79°F)

HINT:

*1: for LHD

*2: for RHD


OK:

The display is as specified in the normal condition.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK AIR DUCT TEMPERATURE SENSOR
2.CHECK AIR DUCT TEMPERATURE SENSOR
E349666E01
2.229,1.625 2.677,1.167 2.677,1.167 2.792,1.167 false 2.031,1.635 1.646,1.188 1.646,1.188 1.5,1.188 false 4.458,0.646 4.625,0.646 false 5.479,2.01 5.479,2.375 false 0.177,0.146 2.573,0.552 2.396,0.406 10 false Component without harness connected: (Air Duct Temperature Sensor) 4.469,0.156 5.625,0.385 1.156,0.229 10 false Resistance (kΩ) 1.365,1.083 1.604,1.302 0.24,0.219 10 false - 2.865,1.073 3.104,1.292 0.24,0.219 10 false + 4.698,0.563 6.677,0.792 1.979,0.229 10 false Maximum per missible value line 4.26,0.417 4.521,0.615 0.26,0.198 10 false 11 4.271,0.625 4.531,0.823 0.26,0.198 10 false 10 4.313,0.813 4.438,1.01 0.125,0.198 10 false 9 4.313,1.01 4.438,1.208 0.125,0.198 10 false 8 4.313,1.219 4.438,1.417 0.125,0.198 10 false 7 4.313,1.427 4.74,1.854 0.427,0.427 10 false 6 4.313,1.635 4.438,1.833 0.125,0.198 10 false 5 4.323,1.833 4.448,2.031 0.125,0.198 10 false 4 4.323,2.021 4.448,2.219 0.125,0.198 10 false 3 4.323,2.219 4.448,2.417 0.125,0.198 10 false 2 4.323,2.438 4.448,2.635 0.125,0.198 10 false 1 4.563,2.427 6.542,2.656 1.979,0.229 10 false Maximum per missible value line 4.333,2.625 4.458,2.823 0.125,0.198 10 false 0 4.479,2.729 4.74,2.927 0.26,0.198 10 false 10 4.438,2.885 4.698,3.083 0.26,0.198 10 false (50) 4.854,2.729 5.115,2.927 0.26,0.198 10 false 20 5.302,2.74 5.563,2.938 0.26,0.198 10 false 30 5.771,2.74 6.031,2.938 0.26,0.198 10 false 40 6.219,2.74 6.479,2.938 0.26,0.198 10 false 50 6.708,2.74 6.969,2.938 0.26,0.198 10 false 60 4.823,2.885 5.083,3.083 0.26,0.198 10 false (68) 5.271,2.885 5.531,3.083 0.26,0.198 10 false (86) 5.688,2.885 6.021,3.083 0.333,0.198 10 false (104) 6.146,2.885 6.479,3.083 0.333,0.198 10 false (122) 6.615,2.885 6.948,3.083 0.333,0.198 10 false (140) 5.198,3.188 6.354,3.417 1.156,0.229 10 false Temperature °C 5.979,3.385 6.271,3.615 0.292,0.229 10 false (°F)

a.

for LHD

i.


b.

for RHD

i.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (-) at 10°C (50°F) 9.4 to 10.5 kΩ
at 15°C (59°F) 7.5 to 8.3 kΩ
at 20°C (68°F) 6.0 to 6.5 kΩ
at 25°C (77°F) 4.5 to 5.2 kΩ
at 30°C (86°F) 3.8 to 4.2 kΩ
at 35°C (95°F) 3.1 to 3.4 kΩ
at 40°C (104°F) 2.5 to 2.8 kΩ
at 45°C (113°F) 2.0 to 2.3 kΩ
at 50°C (122°F) 1.6 to 2.0 kΩ
at 55°C (131°F) 1.3 to 1.6 kΩ
at 60°C (140°F) 1.1 to 1.4 kΩ


NOTICE:
·

Touching the sensor even slightly may change the resistance value. Hold the connector of the sensor.

·

When measuring the resistance, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).

If the resistance value is not as specified, replace the sensor.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR DUCT TEMPERATURE SENSOR)

B

C

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR DUCT TEMPERATURE SENSOR)
E349667E01
0.719,1.813 1.063,2.042 0.344,0.229 5.865,0.99 6.208,1.219 0.344,0.229 1.24,2.396 1.51,2.104 false 1.948,2.354 1.708,2.094 false 5.458,2.979 5.552,2.979 5.552,2.979 5.781,2.594 false 5.615,3.323 5.729,3.323 5.729,3.323 6.031,2.479 false 0.198,0.167 2.51,0.583 2.313,0.417 10 false Front view of wire harness connector: (to Air Duct Temperature Sensor RH) 0.781,1.844 1.135,2.042 0.354,0.198 10 false L12 1.146,2.365 1.354,2.563 0.208,0.198 10 false + 2,2.344 2.208,2.542 0.208,0.198 10 false - 3.896,0.177 6.323,0.552 2.427,0.375 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 5.156,2.906 5.469,3.104 0.313,0.198 10 false TR4 5.26,3.24 5.656,3.438 0.396,0.198 10 false SG-9 5.927,1.01 6.198,1.198 0.271,0.188 10 true E35

a.

for LHD

i.

Disconnect the L12 sensor connector.


ii.

Disconnect the E35 amplifier connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-26 (TR4) - L12-1 (+) Always Below 1 Ω
E35-12 (SG-9) - L12-2 (-)
E35-26 (TR4) - Body ground Always 10 kΩ or higher
E35-12 (SG-9) - Body ground




b.

for RHD

E349667E02
0.719,1.813 1.063,2.042 0.344,0.229 5.865,0.99 6.208,1.219 0.344,0.229 1.24,2.396 1.51,2.104 false 1.948,2.354 1.708,2.094 false 5.448,3.073 5.542,3.073 5.542,3.073 5.771,2.688 false 5.448,3.417 5.563,3.417 5.563,3.417 5.865,2.573 false 0.198,0.167 2.51,0.583 2.313,0.417 10 false Front view of wire harness connector: (to Air Duct Temperature Sensor LH) 0.781,1.844 1.135,2.042 0.354,0.198 10 false K21 1.146,2.365 1.354,2.563 0.208,0.198 10 false + 2,2.344 2.208,2.542 0.208,0.198 10 false - 4.031,0.177 6.458,0.552 2.427,0.375 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 5.01,2.99 5.5,3.188 0.49,0.198 10 false SGND 5.167,3.333 5.438,3.531 0.271,0.198 10 false TR3 5.927,1.01 6.198,1.198 0.271,0.188 10 true E35

i.

Disconnect the K21 sensor connector.


ii.

Disconnect the E35 amplifier connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-25 (TR3) - K21-1 (+) Always Below 1 Ω
E35-34 (SGND) - K21-2 (-)
E35-25 (TR3) - Body ground Always 10 kΩ or higher
E35-34 (SGND) - Body ground





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR