*1: for LHD
*2: for RHD
The rear air mix damper servo motor LH*1or RH*2 sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper servo motor LH*1or RH*2 to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1447/47 | The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the rear air mix damper servo motor. | ·
Rear air mix damper servo motor LH*1 ·
Rear air mix damper servo motor RH*2 ·
No. 2 air conditioning harness assembly ·
Harness or connector ·
Air conditioning amplifier assembly |
*1: for LHD
*2: for RHD
Use the Data List to check if the rear air mix damper servo motor LH*1 or RH*2 is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pls(R) | Rear air mix damper servo motor LH*1 or RH*2 target pulse / Min.: 128, Max.: 383 | for LHD:
·
MAX COLD: 254 (pulse) ·
MAX HOT: 299 (pulse) for RHD:
·
MAX COLD: 258 (pulse) ·
MAX HOT: 213 (pulse) |
·
Displayed between 254 and 299 pulse (for LHD) ·
Displayed between 213 and 258 pulse (for RHD) ·
Rear air mix damper servo motor LH*1 or RH*2 system malfunction |
| Air Mix Servo Actual Pluse(R) | Rear air mix damper servo motor LH*1 or RH*2 actual pulse / Min.: 128, Max.: 383 | for LHD:
·
MAX COLD: 254 (pulse) ·
MAX HOT: 299 (pulse) for RHD:
·
MAX COLD: 258 (pulse) ·
MAX HOT: 213 (pulse) |
·
Displayed between 254 and 299 pulse (for LHD) ·
Displayed between 213 and 258 pulse (for RHD) ·
Rear air mix damper servo motor LH*1 or RH*2 system malfunction |
When the rear temperature adjust switch for driver side is turned from MAX COLD and MAX HOT, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
E
Disconnect the K19 No. 2 air conditioning harness assembly connector.
Disconnect the E36 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K19-2 (RBUG) - E36-12 (RBUG) | Always | Below 1 Ω |
| K19-3 (RBUS) - E36-13 (RBUS) | Always | Below 1 Ω |
| K19-4 (RBBU) - E36-14 (RBBU) | Always | Below 1 Ω |
| K19-2 (RBUG) or E36-12 (RBUG) - Body ground | Always | 10 kΩ or higher |
| K19-3 (RBUS) or E36-13 (RBUS) - Body ground | Always | 10 kΩ or higher |
| K19-4 (RBBU) or E36-14 (RBBU) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the rear air mix damper servo motor LH*1 or RH*2 (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).
*1: for LHD
*2: for RHD
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1447/47 is not output.
A
B
Replace the No. 2 air conditioning harness assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/ Heater)>DISASSEMBLY).
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1447/47 is not output.
OK
NG
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1447/47 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG