Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling Box Blower Motor Circuit  


DESCRIPTION

The cooler blower motor is operated by signals from the air conditioning amplifier assembly (for cool box).

WIRING DIAGRAM

E330415E11
5.448,0.573 5.906,0.771 0.458,0.198 10 false BLW 5.448,1.969 5.906,2.167 0.458,0.198 10 false IG 5.448,2.521 5.906,2.719 0.458,0.198 10 false GND 4.969,0.469 5.146,0.667 0.177,0.198 10 false 7 4.99,1.833 5.167,2.031 0.177,0.198 10 false 2 4.906,2.396 5.115,2.594 0.208,0.198 10 false 12 3.635,0.448 3.813,0.646 0.177,0.198 10 false 2 3.646,0.76 3.823,0.958 0.177,0.198 10 false 1 3.635,1.833 3.813,2.031 0.177,0.198 10 false 1 3.656,2.406 3.833,2.604 0.177,0.198 10 false 6 3.063,1.844 3.24,2.042 0.177,0.198 10 false 1 3.063,2.406 3.24,2.604 0.177,0.198 10 false 6 1.958,2.104 2.865,2.313 0.906,0.208 10 false ECU-IG NO.2 0.167,1.938 1.563,2.167 1.396,0.229 10 false from IG1 NO.1 Relay 1.542,1.24 3.208,1.635 1.667,0.396 10 false Cool Box Blower with Fan Motor Sub-assembly 5.438,2.906 7.01,3.281 1.573,0.375 10 false Air Conditinoing Amplifier Assembly (for Cool Box) 3.542,3.031 5.313,3.417 1.771,0.385 10 false No. 1 Cooler Wiring Harness Assembly Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BATTERY)
a.
E330398E03
0.146,0.083 0.458,0.281 0.313,0.198 10 false *a

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Cooler Wiring Harness Sub-assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BODY GROUND)
a.
E330398E03
0.146,0.083 0.458,0.281 0.313,0.198 10 false *a

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Cooler Wiring Harness Sub-assembly)



OK

3.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY
a.

Replace the No. 1 cooler wiring harness sub-assembly with a normal one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

4.INSPECT COOL BOX BLOWER WITH FAN MOTOR SUB-ASSEMBLY
4.INSPECT COOL BOX BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Remove the cool box blower with fan motor sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(w/ Cool Box)>DISASSEMBLY).


b.

Inspect the cool box blower with fan motor sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(w/ Cool Box)>INSPECTION).

OK:

Cooler blower motor operates smoothly.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG

REPLACE COOL BOX BLOWER WITH FAN MOTOR SUB-ASSEMBLY