Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling Box Control Switch Circuit  


DESCRIPTION

The cooler control switch is the activation switch for the cooling box. If the cooling box does not activate when the cooler control switch is pushed, there may be a malfunction in the circuit shown below.

WIRING DIAGRAM

E160130E06
1.823,0.615 2.375,0.802 0.552,0.188 10 false PANEL 0.146,0.417 1.198,0.625 1.052,0.208 10 false from TAIL Relay 2.677,6.573 2.802,6.74 0.125,0.167 10 false 6 2.677,6.063 2.802,6.229 0.125,0.167 10 false 4 2.677,5.594 2.802,5.76 0.125,0.167 10 false 1 2.698,0.302 2.823,0.469 0.125,0.167 10 false 3 2.906,5.688 3.031,5.854 0.125,0.167 10 false B 2.885,6.188 3.083,6.354 0.198,0.167 10 false +B 2.906,6.656 3.031,6.823 0.125,0.167 10 false L 4.75,6.563 4.875,6.729 0.125,0.167 10 false 4 4.75,6.083 4.875,6.25 0.125,0.167 10 false 1 4.74,5.583 4.865,5.75 0.125,0.167 10 false 2 4.729,5.094 4.854,5.26 0.125,0.167 10 false 7 4.688,4.615 4.875,4.781 0.188,0.167 10 false 10 4.76,4.125 4.885,4.292 0.125,0.167 10 false 5 4.729,2.813 4.854,2.979 0.125,0.167 10 false 1 4.74,2.292 4.865,2.458 0.125,0.167 10 false 2 4.74,1.792 4.865,1.958 0.125,0.167 10 false 4 4.74,1.313 4.865,1.479 0.125,0.167 10 false 3 4.729,0.813 4.854,0.979 0.125,0.167 10 false 6 4.75,0.313 4.875,0.479 0.125,0.167 10 false 5 5.271,6.948 6.875,7.406 1.604,0.458 10 false Air Conditioning Amplifier Assembly (for Cool Box) 5.26,3.156 6.656,3.51 1.396,0.354 10 false Cooler Control Switch Sub-assembly 3.292,7.25 5.094,7.646 1.802,0.396 10 false No. 1 Cooler Wiring Harness Sub-assembly 5.188,6.635 5.708,6.802 0.521,0.167 10 false GND 5.198,6.156 5.719,6.323 0.521,0.167 10 false +B 5.198,5.656 5.719,5.823 0.521,0.167 10 false IG 5.198,5.177 5.719,5.344 0.521,0.167 10 false LED 5.198,4.688 5.719,4.854 0.521,0.167 10 false SG 5.188,4.208 5.708,4.375 0.521,0.167 10 false SW 1.844,5.844 2.354,6.01 0.51,0.167 10 false A/C IG 1.813,6.344 2.396,6.51 0.583,0.167 10 false ECU-B1 0.208,5.698 1.188,6.042 0.979,0.344 10 false from IG1 NO. 2 Relay 0.365,6.167 1.167,6.385 0.802,0.219 10 false from Battery

PROCEDURE

1.INSPECT FUSE (PANEL, A/C IG, ECU-B1)
a.

Remove the PANEL and A/C IG fuses from the cowl side junction block LH.


b.

Remove the ECU-B1 fuse from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PANEL fuse Always Below 1 Ω
ECU-B1 fuse Always Below 1 Ω
A/C IG fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BATTERY)
a.
E158385E47
1.583,1.698 1.063,1.792 false 1.833,1.885 2.271,1.927 false 0.083,0.073 2.948,0.427 2.865,0.354 10 false Front view of wire harness connector: (to No. 1 Cooler Wiring Harness Sub-assembly) 0.906,1.729 1.063,1.875 0.156,0.146 10 false B 2.344,1.833 2.573,2.042 0.229,0.208 10 false +B

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (+B) - Body ground Always 11 to 14 V
1 (B) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BODY GROUND)
a.
E158385E48
1.865,2.104 2.375,2.208 false 0.094,0.115 2.948,0.521 2.854,0.406 10 false Front view of wire harness connector: (to No. 1 Cooler Wiring Harness Sub-assembly) 2.417,2.146 2.76,2.385 0.344,0.24 10 false L

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - Body ground Always Below 1 Ω




OK

4.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)
a.

Replace the No. 1 cooler wiring harness sub-assembly with a normal one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

5.INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY
5.INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY
a.
E158415E02
0.105,0.092 2.725,0.413 2.619,0.321 10 Component with harness connected: (Cooler Control Switch Sub-assembly)

Remove the cooler control switch sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(w/ Cool Box)>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 On Below 1 Ω
1 - 2 Off 10 kΩ or higher



c.

Apply battery voltage to the cooler control switch connector and check that the cooler control switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3
Battery negative (-) → Terminal 4
LED illuminates
Battery positive (+) → Terminal 5
Battery negative (-) → Terminal 6
LED illuminates




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG

REPLACE COOLER CONTROL SWITCH SUB-ASSEMBLY