Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling Box Sensor Circuit  


DESCRIPTION

The No. 3 cooler thermistor is installed on the evaporator in the cooling box unit to detect the cooled air temperature that has passed through the evaporator and control the cooling box. It sends appropriate signals to the air conditioning amplifier assembly (for cool box). The resistance of the No. 3 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly (for cool box) applies voltage (12 V) to the No. 3 cooler thermistor and reads voltage changes as the resistance of the No. 3 cooler thermistor changes.

WIRING DIAGRAM

E160088E04
3.128,2.505 3.284,2.661 0.156,0.156 10 6 3.128,1.929 3.284,2.085 0.156,0.156 10 4 3.128,1.353 3.284,1.509 0.156,0.156 10 1 3.326,1.446 3.482,1.602 0.156,0.156 10 B 3.286,2.029 3.498,2.185 0.212,0.156 10 +B 3.306,2.599 3.462,2.755 0.156,0.156 10 L 5.068,2.485 5.224,2.641 0.156,0.156 10 4 5.068,1.91 5.224,2.065 0.156,0.156 10 1 5.068,1.334 5.224,1.490 0.156,0.156 10 2 3.682,0.619 3.897,0.775 0.214,0.156 10 2 3.682,0.281 3.838,0.437 0.156,0.156 10 1 3.498,0.39 3.654,0.546 0.156,0.156 10 + 3.534,0.705 3.690,0.861 0.156,0.156 10 - 4.989,0.619 5.203,0.775 0.214,0.156 10 10 5.068,0.281 5.224,0.437 0.156,0.156 10 6 5.491,2.589 5.844,2.740 0.354,0.151 10 GND 5.491,2.014 5.844,2.164 0.354,0.151 10 +B 5.491,1.458 5.844,1.608 0.354,0.151 10 IG 5.491,0.707 5.844,0.857 0.354,0.151 10 SG 5.491,0.389 5.844,0.540 0.354,0.151 10 TE 5.509,2.873 7.132,3.443 1.623,0.571 10 Air Conditioning Amplifier Assembly (for Cool Box) 3.684,3.175 5.270,3.521 1.587,0.346 10 No. 1 Cooler Wiring Harness Sub-assembly 0.825,0.591 2.369,0.760 1.544,0.169 10 No. 3 Cooler Thermister 0.247,1.451 1.310,1.763 1.063,0.312 10 from IG1 No. 2 Relay 0.448,2.016 1.256,2.199 0.808,0.183 10 from Battery 1.86,1.645 2.318,1.787 0.458,0.143 10 A/C IG 1.821,2.227 2.377,2.369 0.557,0.143 10 ECU-B1 3.242,2.646 3.282,2.661 0.041,0.014

PROCEDURE

1.INSPECT FUSE (A/C IG, ECU-B1)
a.

Remove the A/C IG fuse from the cowl side junction block LH.


b.

Remove the ECU-B1 fuse from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C IG fuse Always Below 1 Ω
ECU-B1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BATTERY)
a.
E158385E49
1.594,1.667 1.073,1.76 false 1.875,1.875 2.313,1.917 false 0.125,0.073 2.99,0.448 2.865,0.375 10 false Front view of wire harness connector: (to No. 1 Cooler Wiring Harness Sub-assembly) 0.906,1.688 1.063,1.833 0.156,0.146 10 false B 2.344,1.833 2.573,2.042 0.229,0.208 10 false +B

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (+B) - Body ground Always 11 to 14 V
1 (B) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BODY GROUND)
a.
E158385E50
1.865,2.104 2.375,2.208 false 0.104,0.083 2.969,0.5 2.865,0.417 10 false Front view of wire harness connector: (to No. 1 Cooler Wiring Harness Sub-assembly) 2.385,2.146 2.771,2.323 0.385,0.177 10 false L

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - Body ground Always Below 1 Ω




OK

4.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)
a.

Replace the No. 1 cooler wiring harness sub-assembly with a normal one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

5.CHECK NO. 3 COOLER THERMISTOR
5.CHECK NO. 3 COOLER THERMISTOR
a.

Remove the No. 3 cooler thermistor (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(w/ Cool Box)>DISASSEMBLY).

E349829E01
0.583,1.844 0.583,1.323 false 1.771,2.542 1.958,2.365 false 2.292,2.521 2.115,2.354 false 4.219,0.208 5.302,0.406 1.083,0.198 10 false Resistance (kΩ) 4.521,2.542 4.813,2.76 0.292,0.219 10 false -10 4.542,2.719 4.833,2.938 0.292,0.219 10 false (14) 5.063,2.542 5.354,2.76 0.292,0.219 10 false 0 5.542,2.542 5.833,2.76 0.292,0.219 10 false 10 6.135,2.542 6.427,2.76 0.292,0.219 10 false 20 6.646,2.531 6.938,2.75 0.292,0.219 10 false 30 4.979,2.719 5.271,2.938 0.292,0.219 10 false (32) 5.51,2.708 5.802,2.927 0.292,0.219 10 false (50) 6.104,2.708 6.396,2.927 0.292,0.219 10 false (68) 6.615,2.708 6.906,2.927 0.292,0.219 10 false (86) 5.333,3.083 6.417,3.281 1.083,0.198 10 false Temperature °C 6.125,3.292 6.458,3.521 0.333,0.229 10 false (°F) 0.396,1.917 0.99,2.115 0.594,0.198 10 false Sensor 1.646,2.448 1.885,2.646 0.24,0.198 10 false - 2.354,2.438 2.594,2.635 0.24,0.198 10 false + 3.708,1.063 4.052,1.24 0.344,0.177 10 false 10.0 4.25,0.719 4.594,0.896 0.344,0.177 10 false 10.0 4.333,0.885 4.677,1.063 0.344,0.177 10 false 9.0 4.333,1.063 4.677,1.24 0.344,0.177 10 false 8.0 4.333,1.219 4.615,1.396 0.281,0.177 10 false 7.0 4.333,1.375 4.677,1.552 0.344,0.177 10 false 6.0 4.333,1.552 4.677,1.729 0.344,0.177 10 false 5.0 4.333,1.729 4.677,1.906 0.344,0.177 10 false 4.0 4.333,1.896 4.677,2.073 0.344,0.177 10 false 3.0 4.333,2.073 4.677,2.25 0.344,0.177 10 false 2.0 4.323,2.25 4.667,2.427 0.344,0.177 10 false 1.0 4.323,2.438 4.667,2.615 0.344,0.177 10 false 0.0


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (-) -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG