Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling Box Sensor Circuit  


DESCRIPTION

The No. 3 cooler thermistor is installed on the evaporator in the cooling box unit to detect the cooled air temperature that has passed through the evaporator and control the cooling box. It sends appropriate signals to the air conditioning amplifier assembly (for cool box). The resistance of the No. 3 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly (for cool box) applies voltage (12 V) to the No. 3 cooler thermistor and reads voltage changes as the resistance of the No. 3 cooler thermistor changes.

WIRING DIAGRAM

E330397E05
5.521,0.427 5.833,0.625 0.313,0.198 10 false TE 5.531,0.76 5.844,0.958 0.313,0.198 10 false SG 5.531,1.469 5.844,1.667 0.313,0.198 10 false IG 5.531,2.042 5.844,2.24 0.313,0.198 10 false +B 5.531,2.583 5.844,2.781 0.313,0.198 10 false GND 5.052,0.313 5.365,0.51 0.313,0.198 10 false 4 5.052,0.635 5.365,0.833 0.313,0.198 10 false 6 5.052,1.354 5.365,1.552 0.313,0.198 10 false 2 5.052,1.927 5.365,2.125 0.313,0.198 10 false 1 4.979,2.49 5.292,2.688 0.313,0.198 10 false 12 3.563,2.979 5.323,3.375 1.76,0.396 10 false No. 1 Cooler Wiring Harness Sub-assembly 5.469,3 7.031,3.427 1.563,0.427 10 false Air Conditioning Amplifier Assembly (for Cool Box) 0.906,0.542 2.542,0.75 1.635,0.208 10 false No. 3 Cooler Thermistor 1.927,1.615 2.802,1.844 0.875,0.229 10 false ECU-IG NO.2 1.969,2.188 2.844,2.417 0.875,0.229 10 false MPX-B NO.1 3.708,0.313 4.021,0.51 0.313,0.198 10 false 1 3.719,0.635 4.031,0.833 0.313,0.198 10 false 2 3.719,1.354 4.031,1.552 0.313,0.198 10 false 1 3.719,1.917 4.031,2.115 0.313,0.198 10 false 4 3.719,2.49 4.031,2.688 0.313,0.198 10 false 6 3.115,1.354 3.427,1.552 0.313,0.198 10 false 1 3.115,1.917 3.427,2.115 0.313,0.198 10 false 4 3.104,2.49 3.417,2.688 0.313,0.198 10 false 6 0.281,2.031 1.156,2.26 0.875,0.229 10 false from Battery 0.146,1.469 1.125,1.698 0.979,0.229 10 false from IG1 Relay 5.49,2.844 5.802,3.042 0.313,0.198 10 false v1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BATTERY)
a.
E330398E03
0.146,0.083 0.458,0.281 0.313,0.198 10 false *a

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4 - Body ground Always 11 to 14 V
1 - Body ground Engine switch off Below 1 V
1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Cooler Wiring Harness Sub-assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY - BODY GROUND)
a.
E330398E03
0.146,0.083 0.458,0.281 0.313,0.198 10 false *a

Disconnect the No. 1 cooler wiring harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - Body ground Always Below 1 Ω




OK

3.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)
a.

Replace the No. 1 cooler wiring harness sub-assembly with a new or known good one.

OK:

Same problem does not occur.




OK

END (NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY WAS DEFECTIVE)

NG

4.INSPECT NO. 3 COOLER THERMISTOR
4.INSPECT NO. 3 COOLER THERMISTOR

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG