Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

The blower with fan motor sub-assembly is operated by signals from the air conditioning amplifier assembly. The blower with fan motor sub-assembly speed signals are transmitted by changes in the duty ratio.

The air conditioning amplifier assembly controls the blower with fan motor sub-assembly speed.

WIRING DIAGRAM

E330417E04
5.583,0.51 6.042,0.708 0.458,0.198 10 false BLW 5.583,2.073 6.042,2.271 0.458,0.198 10 false GND 5.333,0.396 5.531,0.594 0.198,0.198 10 false 22 5.323,1.969 5.667,2.313 0.344,0.344 10 false 14 4.219,0.385 4.417,0.583 0.198,0.198 10 false 2 4.219,0.781 4.417,0.979 0.198,0.198 10 false 1 2.875,0.385 3.073,0.583 0.198,0.198 10 false 3 2.385,0.656 2.688,0.854 0.302,0.198 10 false HTR 0.844,0.49 1.646,0.688 0.802,0.198 10 false from Battery 3.938,0.51 4.396,0.708 0.458,0.198 10 false SI 3.823,0.927 4.281,1.125 0.458,0.198 10 false GND 3.094,0.5 3.552,0.698 0.458,0.198 10 false +B 2.865,1.302 3.323,1.5 0.458,0.198 10 false A29 2.865,1.469 4.271,1.875 1.406,0.406 10 false Blower with Fan Motor Sub-assembly 5.365,2.604 5.823,2.802 0.458,0.198 10 false E81 5.365,2.781 6.948,3.167 1.583,0.385 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (BLOWER MOTOR)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Blower with fan motor sub-assembly is operated normally using GTS.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BATTERY AND BODY GROUND)
U156814E03
1.313,1.365 1.083,1.74 1.083,1.74 0.833,1.74 false 2.115,1.354 2.354,1.729 2.354,1.729 2.604,1.729 false 0.417,1.01 0.75,1.26 0.333,0.25 10 false A29 0.458,1.646 0.792,1.896 0.333,0.25 10 false GND 2.688,1.635 3.021,1.885 0.333,0.25 10 false +B 0.115,0.104 0.323,0.354 0.208,0.25 10 false *a

a.

Disconnect the blower with fan motor sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-3 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Blower with Fan Motor Sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the A29 blower with fan motor sub-assembly connector.


b.

Disconnect the E81 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A29-2 (SI) - E81-22 (BLW) Always Below 1 Ω
A29-2 (SI) or E81-22 (BLW) - Body ground Always 10 kΩ or higher




OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U156754E03
1.729,0.865 1.969,0.385 1.969,0.385 2.323,0.385 false 0.75,0.792 1.063,1.021 0.313,0.229 10 false A29 0.094,0.083 0.406,0.313 0.313,0.229 10 false *a 2.896,2.823 3.292,3.052 0.396,0.229 10 false GND 2.385,0.271 2.698,0.5 0.313,0.229 10 false SI

Using an oscilloscope, check the waveform

Measurement Condition
Item Content
Terminal No. (Symbol) A29-2 (SI) - Body ground
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition
·

Ignition switch ON

·

Blower switch LO




OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Blower with Fan Motor Sub-assembly)

HINT:

Waveform varies with the blower level.



OK

REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

5.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
5.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Replace the blower with fan motor sub-assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Check that the air conditioning system is operated normally.

OK:

Air conditioning system is operated normally.




OK

END (BLOWER WITH FAN MOTOR SUB-ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY