1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
69195
3.REMOVE BACK DOOR GRIP
Using a moulding remover, detach the 5 claws and open the cover.
Using a T30 "TORX" wrench, remove the 2 screws.
Detach the claw and remove the back door grip.
69478
4.REMOVE LOWER BACK DOOR STOPPER CUSHION
Remove the 4 bolts and 2 lower back door stopper cushions.
67939B
5.REMOVE CENTER BACK DOOR GARNISH
Detach the 5 clips and 4 claws, and remove the center back door garnish.
Disconnect the connector.
81570
6.REMOVE CENTER STOP LIGHT ASSEMBLY
67938A
7.REMOVE BACK DOOR SIDE GARNISH LH
Detach the 3 clips and 2 claws, and remove the back door side garnish LH.
67937B
8.REMOVE BACK DOOR SIDE GARNISH RH
w/o Power Back Door:
Use the same procedure described for the LH side.
w/ Power Back Door:
Detach the clip and 4 claws, and remove the back door side garnish RH.
67847
9.REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)
Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.
| *1 | Power Back Door Rod |
| *2 | Hole of Back Door Service Hole Cover RH |
| *a | Back Door is Half-open |
Detach the 2 clips and separate the back door service hole cover RH, passing the power back door rod through the hole of the back door service hole cover RH.
If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover RH, so do not perform this operation with the back door in a fully open position.
If any of the clips have remained on the back door, remove the clips from the back door and install them to the back door service hole cover RH.
Remove the ball joint bolt, power back door rod and back door stay plate.
Remove the back door service hole cover RH from the power back door rod.
74611B
10.REMOVE ASSIST GRIP (for Face to Face Seat Type)
Remove the 2 screws and assist grip.
67848C
11.REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)
Using a screwdriver, detach the 4 claws and remove the No. 2 back door service hole cover.
Disconnect connector.
84901
12.REMOVE DOOR OPENING SWITCH SUB-ASSEMBLY (for Face to Face Seat Type)
67935B
13.REMOVE BACK DOOR GARNISH
Using a clip remover, detach the 14 clips and remove the back door garnish.
86160T
14.REMOVE REAR HEADER SPEAKER ASSEMBLY (for 14 Speakers)
74623
15.REMOVE REAR ASSIST GRIP REINFORCEMENT (for Face to Face Seat Type)
Remove the 3 bolts.
Detach the 2 claws and remove the rear assist grip reinforcement.
84280D
16.REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)
84270G
17.REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)
Use the same procedure described for the LH side.
18.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)
85143R
19.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)
85110R
20.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
69321
21.REMOVE BACK DOOR LOCK COVER
69350
22.REMOVE BACK DOOR LOCK ASSEMBLY
84930
23.REMOVE DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)
24.REMOVE LICENSE PLATE LIGHT ASSEMBLY (for Standard)
84840G
25.REMOVE BACK DOOR OPENER SWITCH ASSEMBLY
86790D
26.REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Rear View Monitor System)
68281B
27.REMOVE LIFT GATE WEATHERSTRIP
Detach the 25 clips and remove the lift gate weatherstrip.
Do not pull strongly on the lift gate weatherstrip as it may tear.
28.REMOVE CUSHION
Remove the 2 cushions.
67281F
29.REMOVE LOWER BACK DOOR STOPPER
Remove the bolt and lower back door stopper.
81590A
30.REMOVE REAR LIGHT ASSEMBLY LH
81580D
31.REMOVE REAR LIGHT ASSEMBLY RH
Use the same procedure described for the LH side.
76801B
32.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
64886B
33.REMOVE BACK DOOR GLASS CHANNEL LH (w/o Power Back Door)
64885C
34.REMOVE BACK DOOR GLASS CHANNEL RH (w/o Power Back Door)
Use the same procedure described for the LH side.
76085
35.REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)
85345R
36.REMOVE REAR WASHER NOZZLE (w/ Rear Wiper)
68960
37.REMOVE BACK DOOR STAY ASSEMBLY LH
68950C
38.REMOVE BACK DOOR STAY ASSEMBLY RH
Use the same procedure described for the LH side.
58574A
39.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE
64894
40.REMOVE BACK DOOR TRIM COVER LH
Remove the back door trim cover LH as shown in the illustration.
64893
41.REMOVE BACK DOOR TRIM COVER RH
Remove the back door trim cover RH as shown in the illustration.
64780A
42.REMOVE BACK DOOR TRIM PANEL ASSEMBLY
Remove the 4 bolts.
Detach the 16 clips and remove the back door trim panel assembly.
76802C
43.REMOVE NO. 2 BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/ Tire Carrier)
81270
44.REMOVE LICENSE PLATE LIGHT ASSEMBLY (w/ Tire Carrier)
75132C
45.REMOVE REAR LICENSE LIGHT COVER (w/ Tire Carrier)
46.REMOVE REAR BUMPER ASSEMBLY
for Standard:
Remove the rear bumper assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER(for Standard)>REMOVAL).
w/ Towing Hitch:
Remove the rear bumper assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (w/ Towing Hitch)>REMOVAL).
w/ Pintle Hook:
Remove the rear bumper assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER(w/ Pintle Hook)>REMOVAL).
47.REMOVE SPARE TIRE
68870
48.REMOVE LOWER BACK DOOR TORSION BAR ASSEMBLY
Remove the 4 bolts and lower back door torsion bar assembly.
68846B
49.REMOVE BACK DOOR TORSION BAR GUIDE
Detach the 2 claws and remove the back door torsion bar guide.
69291
50.REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY
Remove the screw and back door inside handle.
| *1 | Back Door Handle Grommet |
Remove the back door handle grommet.
69380A
51.REMOVE LOWER TAIL GATE LOCK ASSEMBLY RH
w/o Power Back Door:
Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly RH.
Disconnect the cable from the lower tail gate lock assembly RH.
w/ Power Back Door:
Disconnect the connector.
Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly RH.
69690
52.REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY
w/o Power Back Door:
Remove the 2 screws.
Disconnect the left side cable.
Remove the back door remote control assembly.
w/ Power Back Door:
Disconnect the connector.
Remove the 2 screws and back door remote control assembly.
69390A
53.REMOVE LOWER TAIL GATE LOCK ASSEMBLY LH
w/o Power Back Door:
Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly LH.
w/ Power Back Door:
Disconnect the connector.
Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly LH.
65707A
54.REMOVE TAIL GATE STAY SUB-ASSEMBLY LH
Using a T40 "TORX" socket, remove the 2 screws and tail gate stay sub-assembly LH.
65706A
55.REMOVE TAIL GATE STAY SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
67290
56.REMOVE BACK DOOR DAMPER ASSEMBLY (w/ Power Back Door)
Remove the bolt and back door damper assembly.