Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255724 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53883F 4.REMOVE FRONT FENDER MAIN SEAL LH

Hide 53882H 5.REMOVE FRONT FENDER MAIN SEAL RH

Hide 55781E 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75534 9.REMOVE WINDSHIELD OUTSIDE MOULDING LH

a.
B180565E04
2.021,1.531 2.323,1.792 2.323,1.792 2.323,1.479 false 2.292,1.823 2.479,2.021 0.188,0.198 10 true A

Remove the windshield outside moulding.

i.

Put protective tape around the moulding.


ii.

Using a moulding remover, detach the 6 clips and remove the moulding.

NOTICE:
·

When removing the windshield outside moulding, be careful not to damage the roof drip side finish moulding clip labeled A in the illustration.

·

If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.





Hide 75533 10.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 75548C 11.REMOVE NO. 4 WINDSHIELD MOULDING PAD

a.
B180566

Remove the 4 No. 4 windshield moulding pads.

HINT:

Use the same procedure to remove the 4 pads on the other side.



Hide 75547B 12.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clip(s).


a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B180567E01
2.657,0.28 3.048,0.457 0.391,0.177 10 5 mm

Lightly press the drill against the No. 3 windshield outside moulding clip(s), drill off the flanges of the No. 3 windshield outside moulding clip(s), and remove the No. 3 windshield outside moulding clip(s).

NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Do not pry the No. 3 windshield outside moulding clips with the drill, because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.



NOTICE:

Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.



d.

Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

HINT:

Use the same procedure to remove the clip(s) on the other side.



Hide 75561A 13.REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:

Perform the following procedures if replacing any roof drip side finish moulding clip.


a.

Remove the roof drip side finish moulding clips.

HINT:

Use the same procedure to remove the clip on the other side.



Hide 74330C 22.REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

Hide 74330B 23.REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

Hide 87834 24.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 87810 25.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87810 26.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 89943 27.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 89941 28.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 63310 29.REMOVE ROOF HEADLINING

a.

w/ Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL).




b.

w/o Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL).




Hide 75533G 30.REMOVE WINDSHIELD OUTSIDE MOULDING

a.
B180616E01
1.304,0.179 1.643,0.342 0.338,0.163 10 Cut

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by hand to remove the windshield outside moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 56111 31.REMOVE WINDSHIELD GLASS

HINT:

Be careful not to damage the wire harnesses near the windshield glass with the piano wire.


a.
E271513E01
0.71,1.78 0.826,1.925 0.116,0.145 10 A

w/o Heated Windshield Defroster:

i.

Disconnect the connector A.

HINT:

w/o Heated Windshield Defroster:

The vehicle only has connector A.




b.

w/ Heated Windshield Defroster:

i.

Disconnect the 3 connectors.



c.
B183897E01
0.194,0.173 1.093,0.357 0.899,0.184 10 Plastic Sheet 1.673,2.088 2.697,2.237 1.024,0.149 10 Protective Tape 1.406,3.059 1.965,3.243 0.559,0.184 10 Stopper 1.272,4.09 2.032,4.253 0.760,0.163 10 Piano Wire 1.249,0.266 1.547,0.266 1.547,0.266 1.547,0.943 false 2.211,1.697 2.211,2.068 false 1.101,2.746 1.201,3.156 1.201,3.156 1.33,3.156 false 2.348,2.74 2.248,3.151 2.248,3.151 2.119,3.151 false 1.7,3.557 1.7,4.062 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


d.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




f.
B183898E01
0.81,1.714 1.568,1.882 0.757,0.167 10 Matchmark 1.64,1.105 1.272,1.105 1.272,1.105 1.272,1.706 false 1.64,1.399 1.269,1.399 false

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

NOTICE:

Matchmarks do not need to be placed if not reusing the glass.



g.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the glass.



h.

Disconnect the stoppers.


i.

Using suction cups, remove the glass.


Hide 56116C 32.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a scraper, remove the 2 stoppers.


Hide 56117D 33.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

Using a scraper, remove the dam.


Hide 56165 34.REMOVE FRONT INNER WINDOW MOULDING COVER LH

a.

Using a scraper, remove the cover.


Hide 56111 35.CLEAN WINDSHIELD GLASS

a.
B106929

Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.


b.

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 56115C 36.REMOVE WINDSHIELD GLASS STOPPER

a.

Remove the 2 windshield glass stoppers.


Hide 37.CLEAN VEHICLE BODY

a.
B106081E11
0.377,0.027 1.012,0.204 0.635,0.177 10 Adhesive 1.949,0.07 2.585,0.246 0.635,0.177 10 Adhesive 0.514,1.29 0.11,0.113 0.11,0.113 0.257,0.113 false 2.302,1.428 1.589,0.156 1.589,0.156 1.846,0.156 false

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.