Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, power window rear regulator motor LH, harness or connector.


WIRING DIAGRAM

B184409E02
2.385,0.776 3.733,0.956 1.349,0.180 10 from Main Body ECU 5.499,2.666 6.003,2.836 0.504,0.170 10 DOWN 3.667,2.666 4.129,2.836 0.461,0.170 10 DOWN 5.499,3.139 5.905,3.308 0.406,0.170 10 AUTO 5.499,2.225 5.780,2.395 0.281,0.170 10 UP 5.504,1.121 5.841,1.291 0.338,0.170 10 B 5.504,1.518 5.841,1.688 0.338,0.170 10 GND 0.67,4.264 1.652,4.434 0.982,0.170 10 : LIN Line 3.207,3.272 3.550,3.442 0.343,0.170 10 GND 3.715,3.139 4.135,3.309 0.420,0.170 10 AUTO 3.921,2.225 4.143,2.395 0.222,0.170 10 UP 2.784,3.818 4.741,4.231 1.957,0.413 10 Rear Power Window Regulator Switch Assembly LH 4.971,3.808 6.924,4.261 1.952,0.452 10 Rear Power Window Regulator Motor Assembly LH 0.707,1.081 1.516,1.261 0.809,0.180 10 from Battery 5.228,1.002 5.381,1.155 0.153,0.153 10 2 5.228,1.4 5.381,1.553 0.153,0.153 10 1 5.228,2.128 5.433,2.280 0.204,0.153 10 10 5.228,2.588 5.381,2.740 0.153,0.153 10 7 4.265,2.121 4.417,2.274 0.153,0.153 10 6 4.265,2.569 4.417,2.722 0.153,0.153 10 7 4.265,3.035 4.417,3.188 0.153,0.153 10 8 2.966,3.145 3.118,3.297 0.153,0.153 10 1 2.798,3.632 3.055,3.785 0.257,0.153 10 J10 4.973,3.632 5.231,3.785 0.257,0.153 10 J11 5.228,3.042 5.381,3.194 0.153,0.153 10 4 1.826,1.295 2.934,1.502 1.108,0.206 10 RR DOOR LH

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK FOR DTC (B2312)

NG

2.CHECK FOR DTC (B2312)

OK

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)

NG

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Up SW Rear power window LH manual up signal / ON or OFF ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW Rear power window LH manual down signal / ON or OFF ON: Rear power window LH manual down switch operated
OFF: Rear power window LH switch not operated
-

OK:

The display changes according to operation of the rear power window switch LH.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BODY GROUND)
a.
U164013E01
0.082,0.076 2.703,0.608 2.621,0.532 10 Front view of wire harness connector: (to Rear Power Window Regulator Switch) 0.816,1.704 1.068,1.863 0.253,0.159 10 J10 0.819,2.471 1.153,2.623 0.333,0.152 10 GND 1.149,2.471 1.491,2.151 false

Disconnect the J10 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-1 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)
U156995E03
1.073,2.146 1.51,1.813 false 2.333,2.177 1.906,1.813 false 0.115,0.031 2.521,0.375 2.406,0.344 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.646,1.438 0.927,1.635 0.281,0.198 10 false J11 0.708,2.083 1.063,2.271 0.354,0.188 10 false GND 2.396,2.115 2.604,2.302 0.208,0.188 10 false B

a.

Disconnect the J11 motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J11-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J11-1 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
a.
U164016E02
1.135,1.49 1.604,1.677 false 1.854,1.719 2.333,1.323 false 2.01,1.729 2.448,1.594 false 1.198,3.646 1.573,3.844 false 1.917,3.99 2.281,3.813 false 1.052,4.229 1.469,4.052 false 0.167,2.156 2.646,2.531 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.156,0.031 2.708,0.406 2.552,0.375 10 false Front view of wire harness connector: (to Rear Power Window Regulator Switch) 0.594,1.104 0.844,1.292 0.25,0.188 10 false J10 0.667,3.24 0.906,3.427 0.24,0.188 10 false J11 0.875,1.396 1.156,1.563 0.281,0.167 10 false UP 2.396,1.24 2.875,1.385 0.479,0.146 10 false DOWN 2.469,1.531 2.885,1.698 0.417,0.167 10 false AUTO 2.344,3.719 2.625,3.885 0.281,0.167 10 false UP 0.531,4.198 1.01,4.385 0.479,0.188 10 false DOWN 0.719,3.521 1.135,3.688 0.417,0.167 10 false AUTO

Disconnect the J10 switch connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-6 (UP) - J11-10 (UP) Always Below 1 Ω
J10-7 (DOWN) - J11-7 (DOWN) Always Below 1 Ω
J10-8 (AUTO) - J11-4 (AUTO) Always Below 1 Ω
J10-6 (UP) or J11-10 (UP) - Body ground Always 10 kΩ or higher
J10-7 (DOWN) or J11-7 (DOWN) - Body ground Always 10 kΩ or higher
J10-8 (AUTO) or J11-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

7.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
B184456E25
0.938,3.281 1.531,2.969 false 2.01,2.615 2.521,2.354 false 1.833,2.99 2.615,3.25 false 0.219,1.417 2.917,1.813 2.698,0.396 10 false Component without harness connected: (Rear Power Window Regulator Switch LH) 2.667,3.167 2.906,3.333 0.24,0.167 10 false UP 0.406,3.208 0.875,3.375 0.469,0.167 10 false DOWN 2.594,2.24 3,2.458 0.406,0.219 10 false GND

a.

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J10-6 (UP) - J10-1 (GND) Manual up operation Below 1 Ω
J10-7 (DOWN) - J10-1 (GND) Manual down operation Below 1 Ω




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH