Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

WIRING DIAGRAM

B185318E52
2.938,0.302 3.135,0.448 0.198,0.146 10 false 16 2.573,0.448 2.885,0.615 0.313,0.167 10 false LIN2 0.615,0.802 1,1.031 0.385,0.229 10 false I11 4.125,0.323 4.271,0.469 0.146,0.146 10 false 9 4.292,0.438 4.583,0.604 0.292,0.167 10 false LIN 4.198,0.802 4.615,0.99 0.417,0.188 10 false I12 0.625,0.969 3.365,1.177 2.74,0.208 10 false Multiplex Network Master Switch Assembly 4.198,0.969 6.104,1.313 1.906,0.344 10 false Front Power Window Regulator Motor Assembly LH 0.688,1.458 2.406,1.635 1.719,0.177 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

·

Check that the "D Window Auto Up" and "D Window Auto Down" power window control system customize settings are "ON" before proceeding with work (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>CUSTOMIZE PARAMETERS).

·

After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.



HINT:

If the pulse sensor built into the front power window regulator motor assembly LH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the multiplex network master switch assembly at the auto up position, and opened manually by pushing down the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>FAIL-SAFE CHART).


PROCEDURE

2.CHECK MANUAL UP/DOWN FUNCTION
a.

Check that the driver side door power window moves when the manual up/down function of the multiplex network master switch is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK).

OK:

Driver side door power window moves.




OK

3.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH)

NG

3.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH)
a.

Use the Data List to check if the master switch is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF ON: Driver side power window auto up/down switch operated
OFF: Driver side power window switch not operated
-

OK:

The display changes according to operation of the multiplex network master switch.


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH