Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS (for Double Swing Out Type)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255738 BACK DOOR GLASS(for Double Swing Out Type) A

WINDOW / GLASS  BACK DOOR GLASS(for Double Swing Out Type)  INSTALLATION  


PROCEDURE

Hide 68132D 1.CLEAN BACK DOOR GLASS

a.

Using a scraper, remove the damaged clips, moulding and adhesive sticking to the glass.


b.

Clean the outer circumference of the back door glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP LH (for Outer)

a.

Apply Primer G to the back door glass LH where the clips will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new clips.


c.
U164228E01
0.078,0.056 0.260,0.293 0.182,0.237 10 *a 2.898,0.262 3.080,0.418 0.182,0.155 10 *1 3.205,1.397 3.387,1.552 0.182,0.155 10 *1 2.579,0.579 2.749,0.313 2.749,0.313 2.872,0.313 false

Install the 2 back window glass clips to the back door glass LH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 64828B 3.INSTALL BACK WINDOW GLASS CLIP LH (for Inner)

a.

Apply Primer G to the back door glass LH where the clips will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new clips.


c.
B294132E01
0.059,0.07 0.284,0.320 0.225,0.251 10 *a 1.688,0.264 1.913,0.515 0.225,0.251 10 *1 1.508,1.947 1.733,2.197 0.225,0.251 10 *1 1.272,0.591 1.49,0.346 1.49,0.346 1.662,0.346 false 1.086,2.28 1.304,2.035 1.304,2.035 1.475,2.035 false

Install the 2 back window glass clips to the back door glass LH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 68294B 4.INSTALL NO. 1 BACK DOOR GLASS ADHESIVE DAM (for LH Side)

a.

Apply Primer G to the back door glass LH where the dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new dams.


c.
B293879E01
0.056,0.012 0.289,0.276 0.232,0.264 10 *a 1.463,0.424 1.630,0.622 0.167,0.198 10 *1 1.86,2.497 2.092,2.761 0.232,0.264 10 *1 0.974,0.704 1.292,0.499 1.292,0.499 1.434,0.499 false 2.508,2.787 2.19,2.583 2.19,2.583 2.048,2.583 false

Install the 2 No. 1 back door glass adhesive dams to the back door glass LH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 75573C 5.INSTALL BACK WINDOW OUTSIDE MOULDING (for LH Side)

a.
B293886E02
2.01,2.719 2.115,3.042 2.115,3.042 2.208,3.042 false 2.135,0.875 2.313,1.094 0.177,0.219 10 true A 1.177,2.031 1.5,2.25 0.323,0.219 10 false A - A 2.844,0.729 3.021,0.948 0.177,0.219 10 false A 1.813,2.302 1.938,2.458 0.125,0.156 10 false a 2.24,2.948 2.417,3.104 0.177,0.156 10 false *b 2.052,2 2.188,2.188 0.135,0.188 10 false b 0.49,3.146 0.833,3.302 0.344,0.156 10 false : *1 0.063,0.083 0.25,0.24 0.188,0.156 10 false *a

Apply Primer G to the back door glass LH where the back window outside moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


Standard:
Area Specified Condition
a 10.1 mm (0.398 in.)
b 3.0 mm (0.118 in.)


Text in Illustration
*1 Primer G
*a Backside
*b Ceramic End Line


b.

Remove the peeling paper from a new moulding.


c.

Install the back window outside moulding to the back door glass LH at the location shown in the illustration.

B293887E02
3.469,0.5 3.594,0.708 0.125,0.208 10 false b 3.865,2.156 3.99,2.365 0.125,0.208 10 false c 0.073,0.052 0.292,0.26 0.219,0.208 10 false *a 2.073,1.156 2.219,1.302 0.146,0.146 10 true A 2.635,1.01 2.781,1.156 0.146,0.146 10 false A 4.917,0.76 5.354,0.979 0.438,0.219 10 false A - A 5.833,0.938 6.042,1.115 0.208,0.177 10 false a

Text in Illustration
*a Backside - -

Standard:
Area Specified Condition
a 10.1 mm (0.398 in.)
b 6.1 mm (0.240 in.)
c 4.6 mm (0.181 in.)



Hide 68294A 6.INSTALL BACK DOOR GLASS ADHESIVE DAM (for LH Side)

a.
B293884E02
1.438,2.719 1.333,3.031 1.333,3.031 1.229,3.031 false 1.021,0.708 1.198,0.927 0.177,0.219 10 true A 0.531,1.948 0.854,2.167 0.323,0.219 10 false A - A 0.323,0.698 0.5,0.917 0.177,0.219 10 false A 1.552,2.313 1.677,2.469 0.125,0.156 10 false a 1.313,1.99 1.438,2.146 0.125,0.156 10 false b 1.021,2.938 1.219,3.094 0.198,0.156 10 false *b 0.49,3.115 0.833,3.271 0.344,0.156 10 false : *1 0.063,0.031 0.25,0.188 0.188,0.156 10 false *a

Apply Primer G to the back door glass LH where the back door glass adhesive dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


Standard:
Area Specified Condition
a 11.0 mm (0.433 in.)
b 3.0 mm (0.118 in.)


Text in Illustration
*1 Primer G
*a Backside
*b Ceramic End Line


b.

Remove the peeling paper from a new dam.


c.

Install the back door glass adhesive dam to the back door glass LH at the location shown in the illustration.

B293885E02
2.344,1.156 2.521,1.375 0.177,0.219 10 true A 4.792,0.802 5.115,1.021 0.323,0.219 10 false A - A 1.781,1.167 1.958,1.385 0.177,0.219 10 false A 5.375,0.906 5.5,1.063 0.125,0.156 10 false a 0.781,0.49 0.906,0.646 0.125,0.156 10 false b 0.083,0.052 0.271,0.208 0.188,0.156 10 false *a 0.771,2.146 0.885,2.302 0.115,0.156 10 false c

Text in Illustration
*a Backside - -

Standard:
Area Specified Condition
a 5.8 mm (0.228 in.)
b 7.0 mm (0.276 in.)
c 6.8 mm (0.268 in.)



Hide 68132D 7.INSTALL BACK DOOR GLASS LH

a.
B294129E01
0.49,0.545 0.688,0.717 0.198,0.172 10 *1 0.96,0.628 0.652,0.628 false

Position the glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the back door glass rim is perfectly even.


iii.

Place matchmarks on the back door glass and back door at the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new back door glass. When reinstalling the used back door glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the back door correctly.



iv.

Using suction cups, remove the back door glass.

Text in Illustration
*1 Matchmark



b.
B293888E02
2.021,0.615 2.198,0.615 2.198,0.615 2.438,0.917 false 2.073,1.635 2.26,1.635 2.26,1.635 2.448,1.844 false 2.385,1.958 2.146,2.083 2.146,2.083 1.75,2.083 false 0.5,4.375 0.729,4.552 0.229,0.177 10 false : *1 1.813,0.552 2.042,0.729 0.229,0.177 10 false *1 1.854,1.563 2.083,1.74 0.229,0.177 10 false *1 1.521,1.99 1.75,2.167 0.229,0.177 10 false *2 1.792,0.073 2.021,0.25 0.229,0.177 10 false *a 1.865,1.094 2.094,1.271 0.229,0.177 10 false *b

Using a brush or sponge, apply Primer M to the exposed part of the back door.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


c.

Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

B293892E03
4.594,0.938 4.719,1.188 4.719,1.188 4.813,1.188 false 6.375,0.917 6.5,1.177 6.5,1.177 6.594,1.177 false 4.594,2.073 4.719,2.333 4.719,2.333 4.813,2.333 false 6.417,2.073 6.542,2.333 6.542,2.333 6.635,2.333 false 4.656,3.229 4.781,3.49 4.781,3.49 4.875,3.49 false 6.448,3.229 6.573,3.479 6.573,3.479 6.667,3.479 false 1.563,0.875 1.74,1.094 0.177,0.219 10 false A 0.646,1.49 0.823,1.708 0.177,0.219 10 false B 1.229,1.5 1.406,1.719 0.177,0.219 10 true B 1.75,2.167 1.885,2.323 0.135,0.156 10 false C 2.125,2.823 2.302,3.042 0.177,0.219 10 false D 2.104,2.177 2.281,2.396 0.177,0.219 10 false D 2.438,1.802 2.563,1.99 0.125,0.188 10 true E 2.25,1.281 2.375,1.427 0.125,0.146 10 true F 2.792,1.115 2.917,1.26 0.125,0.146 10 false F 2.979,1.635 3.104,1.781 0.125,0.146 10 false E 1.771,2.823 1.948,3.042 0.177,0.219 10 false C 3.625,0.208 3.948,0.427 0.323,0.219 10 false A - A 5.271,0.208 5.594,0.427 0.323,0.219 10 false B - B 3.625,1.323 4.021,1.542 0.396,0.219 10 false C - C 3.625,2.417 4.021,2.635 0.396,0.219 10 false E - E 5.271,1.323 5.656,1.542 0.385,0.219 10 false D - D 5.271,2.417 5.656,2.635 0.385,0.219 10 false F - F 1.563,1.354 1.74,1.573 0.177,0.219 10 false A 4.375,0.594 4.5,0.75 0.125,0.156 10 false a 4.625,0.354 4.75,0.51 0.125,0.156 10 false b 4.844,1.104 5.063,1.26 0.219,0.156 10 false *b 0.635,3.448 0.979,3.604 0.344,0.156 10 false : *1 0.083,0.115 0.302,0.323 0.219,0.208 10 false *a 5.906,2.146 6.021,2.302 0.115,0.156 10 false c 6.396,0.354 6.521,0.51 0.125,0.156 10 false b 6.042,0.552 6.167,0.708 0.125,0.156 10 false c 4.625,1.5 4.75,1.656 0.125,0.156 10 false b 6.448,1.656 6.573,1.813 0.125,0.156 10 false b 4.667,2.521 4.792,2.677 0.125,0.156 10 false b 6.458,2.51 6.583,2.667 0.125,0.156 10 false b 4.344,1.729 4.469,1.885 0.125,0.156 10 false d 4.24,2.823 4.365,2.979 0.125,0.156 10 false e 5.927,2.823 6.052,2.979 0.125,0.156 10 false f 6.625,1.094 6.844,1.25 0.219,0.156 10 false *b 4.844,2.24 5.063,2.396 0.219,0.156 10 false *b 6.677,2.26 6.896,2.417 0.219,0.156 10 false *b 4.896,3.396 5.115,3.552 0.219,0.156 10 false *b 6.688,3.406 6.906,3.563 0.219,0.156 10 false *b

Text in Illustration
*1 Primer G - -
*a Backside *b Ceramic End Line

Standard:
Area Specified Condition
a 15.3 mm (0.602 in.)
b 3.0 mm (0.118 in.)
c 20.0 mm (0.787 in.)
d 17.0 mm (0.669 in.)
e 29.0 mm (1.14 in.)
f 37.0 mm (1.46 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.




d.

Apply adhesive to the back door glass LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass LH as shown in the illustration.

B293893E02
1.448,2.021 1.448,2.354 false 2.583,2.031 2.813,2.24 2.813,2.24 3.031,2.24 false 4.479,1.25 4.75,0.979 4.75,0.979 4.865,0.979 false 6.271,1.24 6.469,0.896 6.469,0.896 6.625,0.896 false 4.427,2.646 4.688,2.385 4.688,2.385 4.802,2.385 false 5.646,2.656 6.198,2.271 6.198,2.271 5.875,2.656 false 1.563,0.292 1.74,0.51 0.177,0.219 10 false A 0.646,0.906 0.823,1.125 0.177,0.219 10 false B 1.229,0.906 1.406,1.125 0.177,0.219 10 true B 2.219,1.75 2.396,1.969 0.177,0.219 10 false C 2.802,0.521 2.979,0.74 0.177,0.219 10 false D 2.188,0.708 2.365,0.927 0.177,0.219 10 true D 2.229,2.125 2.406,2.344 0.177,0.219 10 false C 3.625,0.656 3.948,0.875 0.323,0.219 10 false A - A 5.271,0.656 5.594,0.875 0.323,0.219 10 false B - B 3.625,1.885 4.021,2.104 0.396,0.219 10 false C - C 5.271,1.885 5.656,2.104 0.385,0.219 10 false D - D 1.563,0.76 1.74,0.979 0.177,0.219 10 false A 0.344,3.104 0.469,3.26 0.125,0.156 10 false a 2.615,2.844 2.74,3 0.125,0.156 10 false a 0.792,2.656 0.917,2.813 0.125,0.156 10 false b 3.073,2.917 3.198,3.073 0.125,0.156 10 false b 0.979,3.177 1.323,3.333 0.344,0.156 10 false : *1 3.052,2.167 3.281,2.323 0.229,0.156 10 false *2 4.885,0.917 5.115,1.073 0.229,0.156 10 false *2 1.375,2.375 1.604,2.531 0.229,0.156 10 false *3 0.094,0.125 0.281,0.281 0.188,0.156 10 false *a 4.604,1.594 4.719,1.75 0.115,0.156 10 false c 6.458,1.594 6.573,1.75 0.115,0.156 10 false d 4.552,3.042 4.667,3.198 0.115,0.156 10 false e 5.719,3.042 5.833,3.198 0.115,0.156 10 false b 6.167,3.115 6.281,3.271 0.115,0.156 10 false f 6.635,0.833 6.865,0.99 0.229,0.156 10 false *2 4.823,2.323 5.052,2.479 0.229,0.156 10 false *2 6.219,2.167 6.448,2.323 0.229,0.156 10 false *2

Text in Illustration
*1 Adhesive *2 Adhesive Center Line
*3 Ceramic Notch - -
*a Backside - -

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 11.3 mm (0.445 in.)
d 16.0 mm (0.630 in.)
e 13.0 mm (0.512 in.)
f 25.0 mm (0.984 in.)




e.

Install the back door glass LH to the vehicle body.

i.

Hold the back door glass securely in place with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the outer surface of the back door glass to ensure that the back door glass is securely attached to the vehicle body.


iii.
B180606E02
1.756,1.426 1.979,1.623 0.223,0.198 10 *1 0.978,1.467 1.709,1.525 false

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive to any areas where the amount of adhesive is inadequate.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours


Text in Illustration
*1 Adhesive


iv.

Connect the connectors.



Hide 68131C 8.CLEAN BACK DOOR GLASS RH

HINT:

Use the same procedure described for the LH side.


Hide 64827A 9.INSTALL BACK WINDOW GLASS CLIP RH (for Outer)

a.
U164229E02
0.917,1.792 1.24,1.708 1.24,1.708 1.365,1.708 false 0.083,0.063 0.344,0.344 0.26,0.281 10 false *a 1.906,0.323 2.135,0.552 0.229,0.229 10 false *1 1.406,1.625 1.635,1.854 0.229,0.229 10 false *1

Apply Primer G to the back door glass RH where the clips will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new clips.


c.

Install the 2 back window glass clips to the back door glass RH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 64827B 10.INSTALL BACK WINDOW GLASS CLIP RH (for Inner)

a.

Apply Primer G to the back door glass RH where the clips will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new clips.


c.
B294134E01
0.063,0.063 0.334,0.253 0.271,0.190 10 *a 1.822,0.212 2.092,0.402 0.271,0.190 10 *1 1.942,1.663 2.213,1.853 0.271,0.190 10 *1 2.426,0.504 2.144,0.287 2.144,0.287 2.001,0.287 false 2.557,1.976 2.275,1.759 2.275,1.759 2.132,1.759 false

Install the 2 back window glass clips to the back door glass RH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 68294A 11.INSTALL NO. 1 BACK DOOR GLASS ADHESIVE DAM (for RH Side)

a.

Apply Primer G to the back door glass RH where the dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 3 new dams.


c.
B293878E01
0.064,0.055 0.276,0.247 0.211,0.192 10 *a 1.57,0.497 1.781,0.689 0.211,0.192 10 *1 1.094,0.726 1.419,0.575 1.419,0.575 1.541,0.575 false 2.551,2.702 2.762,2.893 0.211,0.192 10 *1 2.075,2.93 2.4,2.779 2.4,2.779 2.522,2.779 false

Install the 3 No. 1 back door glass adhesive dams to the back door glass RH at the locations shown in the illustration.

Text in Illustration
*1 Ceramic Notch
*a Backside


Hide 75573C 12.INSTALL BACK WINDOW OUTSIDE MOULDING (for RH Side)

a.
B293882E02
1.677,2.854 1.5,3.146 1.5,3.146 1.385,3.146 false 0.896,0.844 1.073,1.063 0.177,0.219 10 true A 0.771,2.021 1.094,2.24 0.323,0.219 10 false A - A 0.198,0.656 0.375,0.875 0.177,0.219 10 false A 1.792,2.427 1.917,2.583 0.125,0.156 10 false a 1.542,2.083 1.667,2.24 0.125,0.156 10 false b 1.198,3.052 1.427,3.208 0.229,0.156 10 false *b 0.51,3.146 0.854,3.302 0.344,0.156 10 false : *1 0.167,0.073 0.354,0.229 0.188,0.156 10 false *a

Apply Primer G to the back door glass RH where the back window outside moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


Standard:
Area Specified Condition
a 10.1 mm (0.398 in.)
b 3.0 mm (0.118 in.)


Text in Illustration
*1 Primer G
*a Backside
*b Ceramic End Line


b.

Remove the peeling paper from a new moulding.


c.

Install the back window outside moulding to the back door glass RH at the location shown in the illustration.

B293883E02
0.885,0.365 1,0.531 0.115,0.167 10 false b 0.5,2.177 0.625,2.385 0.125,0.208 10 false c 1.677,0.969 1.823,1.115 0.146,0.146 10 false A 0.083,0.063 0.292,0.26 0.208,0.198 10 false *a 2.25,1.115 2.406,1.302 0.156,0.188 10 true A 4.906,0.563 5.344,0.781 0.438,0.219 10 false A - A 5.396,0.875 5.604,1.052 0.208,0.177 10 false a

Text in Illustration
*a Backside - -

Standard:
Area Specified Condition
a 10.1 mm (0.398 in.)
b 5.7 mm (0.224 in.)
c 4.6 mm (0.181 in.)



Hide 68294A 13.INSTALL BACK DOOR GLASS ADHESIVE DAM (for RH Side)

a.
B293880E01
3.265,0.654 3.398,0.870 0.133,0.216 10 A 0.959,1.918 1.286,2.134 0.327,0.216 10 A - A 2.561,0.642 2.740,0.859 0.179,0.216 10 A 1.604,2.27 1.728,2.426 0.125,0.156 10 a 1.84,1.924 1.965,2.080 0.125,0.156 10 b 2.009,2.921 2.239,3.077 0.231,0.156 10 *b 0.493,3.108 0.836,3.264 0.343,0.156 10 : *1 0.115,0.049 0.305,0.205 0.191,0.156 10 *a 1.805,2.701 1.912,3.019 1.912,3.019 1.995,3.019 false

Apply Primer G to the back door glass RH where the back window outside moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


Standard:
Area Specified Condition
a 11.0 mm (0.433 in.)
b 3.0 mm (0.118 in.)


Text in Illustration
*1 Primer G
*a Backside
*b Ceramic End Line


b.

Remove the peeling paper from a new moulding.


c.

Install the back window outside moulding to the back door glass RH at the location shown in the illustration.

B293881E02
3.875,2.156 4.073,2.156 false 4.083,2.073 4.302,2.281 0.219,0.208 10 false *b 2.573,1.083 2.719,1.229 0.146,0.146 10 false A 0.125,0.094 0.333,0.292 0.208,0.198 10 false *a 3.177,1.083 3.323,1.229 0.146,0.146 10 false A 4.156,0.479 4.302,0.625 0.146,0.146 10 false b 5.177,0.667 5.615,0.885 0.438,0.219 10 false A - A 6.083,0.875 6.292,1.052 0.208,0.177 10 false a

Text in Illustration
*a Backside *b R End

Standard:
Area Specified Condition
a 2.8 mm (0.110 in.)
b 6.8 mm (0.268 in.)



Hide 68131C 14.INSTALL BACK DOOR GLASS RH

a.
B294130E01
3.056,0.539 3.253,0.711 0.198,0.172 10 *1 2.682,0.63 3.048,0.63 false

Position the glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the back door glass rim is perfectly even.


iii.

Place matchmarks on the back door glass and back door at the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new back door glass. When reinstalling the used back door glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the back door correctly.



iv.

Using suction cups, remove the back door glass.

Text in Illustration
*1 Matchmark



b.
B293889E01
0.495,4.33 0.724,4.503 0.229,0.173 10 : *1 2.024,0.577 2.201,0.577 2.201,0.577 2.442,0.883 false 2.062,1.612 2.245,1.612 2.245,1.612 2.44,1.821 false 2.383,1.937 2.148,2.061 2.148,2.061 1.753,2.061 false 1.806,0.498 2.035,0.671 0.229,0.173 10 *1 1.846,1.526 2.074,1.699 0.229,0.173 10 *1 1.558,1.979 1.787,2.152 0.229,0.173 10 *2 1.81,0.063 2.039,0.236 0.229,0.173 10 *a 1.809,1.065 2.038,1.239 0.229,0.173 10 *b

Using a brush or sponge, apply Primer M to the exposed part of the back door.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


c.

Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

B293890E03
4.698,0.969 4.771,1.188 4.771,1.188 4.823,1.188 false 6.625,0.969 6.698,1.188 6.698,1.188 6.75,1.188 false 4.771,2.135 4.833,2.365 4.833,2.365 4.896,2.365 false 6.573,2.135 6.635,2.354 6.635,2.354 6.698,2.354 false 4.75,3.125 4.823,3.344 4.823,3.344 4.875,3.344 false 1.729,0.906 1.906,1.125 0.177,0.219 10 false A 0.594,1.49 0.708,1.635 0.115,0.146 10 false B 1.146,1.698 1.323,1.917 0.177,0.219 10 true B 2.792,1.5 2.969,1.719 0.177,0.219 10 false F 3.344,1.5 3.521,1.719 0.177,0.219 10 false F 1.854,2.25 2.031,2.469 0.177,0.219 10 false D 1.865,2.656 2.042,2.875 0.177,0.219 10 false D 2.552,2.646 2.729,2.865 0.177,0.219 10 false E 2.583,2.24 2.76,2.458 0.177,0.219 10 false E 3.865,0.396 4.188,0.615 0.323,0.219 10 false A - A 5.5,0.396 5.823,0.615 0.323,0.219 10 false B - B 3.865,1.417 4.26,1.635 0.396,0.219 10 false C - C 5.5,1.417 5.885,1.635 0.385,0.219 10 false D - D 1.729,1.385 1.906,1.604 0.177,0.219 10 false A 6.073,0.552 6.198,0.708 0.125,0.156 10 false b 0.667,3.458 1.01,3.615 0.344,0.156 10 false : *1 0.094,0.094 0.281,0.25 0.188,0.156 10 false *a 0.385,2.073 0.542,2.219 0.156,0.146 10 false C 0.917,2.24 1.073,2.385 0.156,0.146 10 false C 3.865,2.417 4.26,2.635 0.396,0.219 10 false E - E 5.5,2.417 5.885,2.635 0.385,0.219 10 false F - F 4.719,0.5 4.917,0.698 0.198,0.198 10 false a 4.844,1.125 5.042,1.323 0.198,0.198 10 false *b 6.646,0.25 6.844,0.448 0.198,0.198 10 false a 4.323,1.729 4.521,1.927 0.198,0.198 10 false c 4.781,1.427 4.979,1.625 0.198,0.198 10 false a 4.76,2.438 4.958,2.635 0.198,0.198 10 false a 4.531,2.76 4.635,2.958 0.104,0.198 10 false d 6.354,2.615 6.458,2.813 0.104,0.198 10 false e 6.573,1.708 6.771,1.906 0.198,0.198 10 false a 6.771,1.125 6.969,1.323 0.198,0.198 10 false *b 4.906,2.292 5.104,2.49 0.198,0.198 10 false *b 6.708,2.292 6.906,2.49 0.198,0.198 10 false *b 4.896,3.281 5.094,3.479 0.198,0.198 10 false *b

Text in Illustration
*1 Primer G - -
*a Backside *b Ceramic End Line

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 37.0 mm (1.46 in.)
c 29.0 mm (1.14 in.)
d 17.0 mm (0.670 in.)
e 20.0 mm (0.787 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.

·

Do not apply primer outside the ceramic area.




d.

Apply adhesive to the back door glass RH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass RH as shown in the illustration.

U164226E01
1.834,1.741 2.001,1.952 0.166,0.211 1.129,1.115 1.296,1.411 0.166,0.296 1.724,0.35 1.903,0.566 0.179,0.216 10 A 0.589,0.929 0.768,1.145 0.179,0.216 10 B 1.148,1.133 1.327,1.349 0.179,0.216 10 B 1.867,1.71 2.046,1.926 0.179,0.216 10 C 3.555,0.916 3.734,1.133 0.179,0.216 10 D 2.778,0.917 2.957,1.133 0.179,0.216 10 D 1.885,2.09 2.064,2.307 0.179,0.216 10 C 3.902,0.338 4.229,0.554 0.327,0.216 10 A - A 5.546,0.338 5.873,0.554 0.327,0.216 10 B - B 3.856,1.986 4.257,2.202 0.401,0.216 10 C - C 5.546,1.968 5.931,2.184 0.384,0.216 10 D - D 1.725,0.822 1.904,1.038 0.179,0.216 10 A 0.303,3.12 0.428,3.276 0.125,0.156 10 a 0.773,2.647 0.897,2.803 0.125,0.156 10 b 1.028,3.146 1.372,3.302 0.343,0.156 10 : *1 1.076,2.359 1.308,2.515 0.232,0.156 10 *2 2.585,2.181 2.817,2.337 0.232,0.156 10 *3 0.06,0.057 0.250,0.213 0.191,0.156 10 *a 1.16,2.009 1.16,2.338 false 2.681,2.003 2.681,2.162 false 2.603,2.83 2.728,2.986 0.125,0.156 10 a 3.056,2.904 3.181,3.060 0.125,0.156 10 b 4.555,1.608 4.680,1.764 0.125,0.156 10 c 6.321,1.671 6.445,1.827 0.125,0.156 10 d 4.537,3.016 4.661,3.172 0.125,0.156 10 e 6.255,3.011 6.380,3.167 0.125,0.156 10 e 5.844,1.554 5.969,1.710 0.125,0.156 10 b 4.957,0.855 5.188,1.011 0.232,0.156 10 *2 4.905,2.272 5.137,2.428 0.232,0.156 10 *2 6.563,2.185 6.794,2.341 0.232,0.156 10 *2 6.353,0.665 6.584,0.821 0.232,0.156 10 *2 6.107,2.652 6.398,2.249 6.398,2.249 6.536,2.249 false

Text in Illustration
*1 Adhesive *2 Adhesive Center Line
*3 Ceramic Notch - -
*a Backside - -

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 11.3 mm (0.445 in.)
d 25.0 mm (0.984 in.)
e 13.0 mm (0.512 in.)




e.

Install the back door glass RH to the vehicle body.

i.

Hold the back door glass securely in place with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the outer surface of the back door glass to ensure that the back door glass is securely attached to the vehicle body.


iii.
B180606E02
1.756,1.426 1.979,1.623 0.223,0.198 10 *1 0.978,1.467 1.709,1.525 false

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive to any areas where the amount of adhesive is inadequate.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours


Text in Illustration
*1 Adhesive


iv.

Connect the connectors.



Hide 68132D 15.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 64790C 16.INSTALL BACK DOOR TRIM PANEL ASSEMBLY LH (for LH Side)

Hide 69278D 17.INSTALL DOOR INSIDE HANDLE BEZEL LH (for LH Side)

Hide 67884A 19.INSTALL BACK DOOR CENTER WEATHERSTRIP (for RH Side)

Hide 20.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 64780C 21.INSTALL BACK DOOR TRIM PANEL ASSEMBLY RH (for RH Side)

Hide 64791C 22.INSTALL BACK DOOR TRIM COVER RH (for RH Side)

Hide 51903B 24.INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51902A 25.INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51937C 26.INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

Hide 42652A 27.INSTALL SPARE TIRE (w/ Tire Carrier)