Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING › from 2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255741 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Temporarily install the housing with the 8 bolts (vehicle body side) and 8 nuts.


b.

Tighten the 8 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Tighten the 8 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

B178615


Hide 63201P 2.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.
B178614

Using a T25 "TORX" driver, temporarily install the glass with the 4 screws.


b.

Perform a level check.

B178629E06
5.292,0.708 5.625,0.885 0.333,0.177 10 false Even 4.688,1.198 4.844,1.375 0.156,0.177 10 false a 1.896,1.854 2.052,2.031 0.156,0.177 10 false A 2.167,1.854 2.323,2.031 0.156,0.177 10 false A 2.458,1.854 2.615,2.031 0.156,0.177 10 false B 2.74,1.854 2.896,2.031 0.156,0.177 10 true B 2.333,2.323 2.49,2.5 0.156,0.177 10 true D 2.479,2.49 2.635,2.667 0.156,0.177 10 true D 2.115,1.052 2.271,1.229 0.156,0.177 10 true C 2.125,1.333 2.281,1.51 0.156,0.177 10 true C

i.

Check the difference in the level between the roof panel and the upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

Standard:
Area Specified Condition
A - A -1.5 to +1.5 mm (-0.0591 to +0.0591 in.)
B - B
C - C
D - D -1.0 to +1.5 mm (-0.0394 to +0.0591 in.)


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.



ii.

Perform a gap check.

Check the gap between the roof panel and roof glass.

NOTICE:

The gap must be even all around.




c.
B178614

Tighten the 4 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 3.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218G 4.INSTALL SLIDING ROOF SIDE GARNISH LH

B178613

a.

Attach the 5 claws to install the sliding roof side garnish.


Hide 63217K 5.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 88566V 6.INSTALL REAR NO. 5 ROOF AIR DUCT

a.
B178612

Attach the 2 clips to install the duct.


Hide 88566U 7.INSTALL REAR NO. 4 ROOF AIR DUCT

HINT:

Use the same procedures described for the No. 5 roof air duct.


Hide 62180A 8.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 9.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 10.INSTALL ROOF HEADLINING ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 12.CHECK SRS WARNING LIGHT