Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255746 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

a.

Pass the hood lock control cable assembly into the engine room.


b.

Pass the cable rear side through the grommet until the cable stopper is attached to the grommet.


c.

Pass the cable front side through the upper radiator support.


d.

Connect the 6 clamps shown in the illustration.

B426530E09
3.439,0.979 3.439,1.119 3.439,1.119 3.53,1.119 false 4.63,0.902 4.63,1.042 4.63,1.042 4.721,1.042 false 1.974,2.646 1.974,2.786 1.974,2.786 1.815,2.786 false 3.473,3.137 3.473,3.277 3.473,3.277 3.314,3.277 false 4.538,3.27 4.538,3.41 4.538,3.41 4.638,3.41 false 5.649,2.804 5.649,3.077 5.649,3.077 5.811,3.077 false 5.827,2.981 5.983,3.163 0.156,0.181 10 *a 4.655,3.325 4.811,3.506 0.156,0.181 10 *a 3.098,3.182 3.254,3.363 0.156,0.181 10 *a 1.622,2.696 1.778,2.878 0.156,0.181 10 *a 3.527,1.029 3.683,1.210 0.156,0.181 10 *a 4.746,0.952 4.902,1.133 0.156,0.181 10 *a

Text in Illustration
*a Clamp - -


Hide 53630 2.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

a.

Pass the hood lock control cable assembly into the engine room.


b.

Pass the cable rear side through the grommet until the cable stopper is attached to the grommet.


c.

Pass the cable front side through the upper radiator support.


d.

Connect the 6 clamps shown in the illustration.

B421447E04
1.729,1.583 1.646,1.583 false 2.615,0.708 2.615,0.552 2.615,0.552 2.771,0.552 false 5.083,0.646 5.01,0.427 5.01,0.427 4.875,0.427 false 4.719,3.031 4.719,3.396 4.719,3.396 4.844,3.396 false 3.5,3.281 3.427,3.406 3.427,3.406 3.479,3.406 false 2.156,2.927 2.073,2.927 false 2.792,0.469 2.948,0.646 0.156,0.177 10 false *a 1.49,1.49 1.646,1.667 0.156,0.177 10 false *a 4.698,0.323 4.854,0.5 0.156,0.177 10 false *a 4.885,3.313 5.042,3.49 0.156,0.177 10 false *a 3.531,3.344 3.688,3.521 0.156,0.177 10 false *a 1.906,2.844 2.063,3.021 0.156,0.177 10 false *a

Text in Illustration
*a Clamp - -


Hide 53601 3.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B310743

Connect the hood lock control cable assembly and attach the 2 claws to install the hood lock lever sub-assembly.


Hide 53510 4.INSTALL HOOD LOCK ASSEMBLY

a.
B181067

Apply MP grease to the sliding areas of the hood lock assembly.


b.
B188476E04
0.042,0.042 0.802,0.323 0.76,0.281 12 false for LHD: 0.042,2.063 0.844,2.583 0.802,0.521 12 true for RHD:

Connect the hood lock control cable assembly.


c.

Install the hood lock assembly.


d.
B188475E04
0.042,0.042 0.802,0.323 0.76,0.281 12 false for LHD: 0.042,2.427 1.031,2.917 0.99,0.49 12 true for RHD:

Install the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Connect the connector.


Hide 53629 5.INSTALL HOOD LOCK CONTROL CABLE COVER

a.
B188474E05
0.042,0.042 0.802,0.323 0.76,0.281 12 false for LHD: 0.042,2.427 0.927,2.906 0.885,0.479 12 true for RHD:

Attach the claw to install the hood lock control cable cover.


b.

Install the 3 screws.


Hide 53228A 6.REMOVE LOWER NO. 1 RADIATOR MOUNTING BRACKET

a.
B431647

Install the lower No. 1 radiator mounting bracket with the bolt.


Hide 53883F 7.INSTALL FRONT FENDER MAIN SEAL LH (for LHD)

a.
B426539

Attach the 3 clips to install the front fender main seal LH.


Hide 53882H 8.INSTALL FRONT FENDER MAIN SEAL RH (for RHD)

a.
B421444

Attach the 3 clips to install the front fender main seal RH.