A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
w/ Dynamic Radar Cruise Control System:
When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
52521
1.INSTALL FRONT BUMPER UPPER CENTER RETAINER
Attach the guide to install the front bumper upper center retainer.
Install the 3 bolts.
81150
2.INSTALL HEADLIGHT ASSEMBLY LH
for Halogen Headlight:
(See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>INSTALLATION)
for LED Headlight:
(See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>INSTALLATION)
for Halogen Headlight and LED Headlight:
81110
3.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure described for the LH side.
52116A
4.INSTALL FRONT BUMPER SIDE SUPPORT LH
Attach the 3 claws to install the front bumper side support LH.
Install the 2 screws.
52115A
5.INSTALL FRONT BUMPER SIDE SUPPORT RH
Use the same procedure described for the LH side.
52113D
6.INSTALL FRONT BUMPER EXTENSION LH
Install the front bumper extension LH with the 3 bolts.
52112D
7.INSTALL FRONT BUMPER EXTENSION RH
Use the same procedure described for the LH side.
52119A
8.INSTALL FRONT BUMPER COVER
w/ Dynamic Radar Cruise Control System:
Connect the connector.
w/ Multi-terrain Monitor:
Connect the connector.
w/ Fog Light:
Connect the No. 4 engine room wire connector.
Connect the winch control wire connector and attach the 6 claws to install the front bumper cover.
Install the 3 clips, 5 screws and 4 bolts.
Using a T30 "TORX" socket, install the 6 screws.
53182
9.INSTALL HEADLIGHT COVER LH (w/ Headlight Cover)
Attach the 5 claws and headlight cover LH.
53181
10.INSTALL HEADLIGHT COVER RH (w/ Headlight Cover)
Use the same procedure described for the LH side.
53292A
11.INSTALL UPPER RADIATOR SUPPORT SEAL
Install the upper radiator support seal with the 7 clips.
52049
12.INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY
Attach the 2 guides to install the front bumper winch cover sub-assembly.
Attach the 2 claws.
53806
13.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
Push in the clip to install the front fender splash shield sub-assembly LH.
Install the 3 bolts and screw.
53805
14.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
Push in the clip to install the front fender splash shield sub-assembly RH.
Install the 3 bolts and 2 screws.
15.ADJUST HEADLIGHT AIMING
for Halogen Headlight:
(See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>ADJUSTMENT)
for LED Headlight:
(See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>ADJUSTMENT)
for Halogen Headlight and LED Headlight:
16.ADJUST FOG LIGHT AIMING (w/ Fog Light)
17.INSPECT TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System)
86790B
18.ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)