Home › Vehicle Exterior › DOOR / HATCH › TAIL GATE CLOSER SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255760 TAIL GATE CLOSER SYSTEM J

DOOR / HATCH  TAIL GATE CLOSER SYSTEM  Tail Gate does not Open with Back Door Remote Control  


WIRING DIAGRAM

B312264E04
1.854,1.031 2.063,1.177 0.208,0.146 10 false h3 2.458,0.563 2.552,0.708 0.094,0.146 10 false 1 3.521,0.563 3.615,0.708 0.094,0.146 10 false 2 1.854,1.188 4.198,1.458 2.344,0.271 10 false Back Door Remote Control Assembly 5.604,2.177 5.708,2.323 0.104,0.146 10 false 3 5.563,0.479 5.729,0.625 0.167,0.146 10 false 19 5.604,3.469 5.698,3.615 0.094,0.146 10 false 8 5.604,4.76 5.698,4.906 0.094,0.146 10 false 2 5.594,6.052 5.698,6.198 0.104,0.146 10 false 1 3.135,2.271 4.167,2.417 1.031,0.146 10 false 5 3.146,3.542 4.177,3.688 1.031,0.146 10 false 6 3.135,4.865 4.167,5.01 1.031,0.146 10 false 5 3.135,6.135 4.167,6.281 1.031,0.146 10 false 6 2.625,2.531 3.01,2.677 0.385,0.146 10 false ACT+ 2.625,3.802 3.01,3.948 0.385,0.146 10 false ACT- 1.74,2.958 2.771,3.292 1.031,0.333 10 false Lower Tail Gate Lock Motor LH 1.01,4.094 2.042,4.24 1.031,0.146 10 false h5 1.01,4.26 3.198,4.406 2.188,0.146 10 false Lower Tail Gate Lock Assembly LH 1.01,6.688 2.042,6.833 1.031,0.146 10 false h4 1.01,6.865 3.229,7.125 2.219,0.26 10 false Lower Tail Gate Lock Assembly RH 2.625,5.094 3.01,5.24 0.385,0.146 10 false ACT+ 2.625,6.385 3.01,6.531 0.385,0.146 10 false ACT- 1.729,5.531 2.781,5.927 1.052,0.396 10 false Lower Tail Gate Lock Motor RH 5.521,6.26 5.792,6.406 0.271,0.146 10 false L51 5.521,4.979 5.792,5.125 0.271,0.146 10 false L51 5.521,3.688 5.792,3.833 0.271,0.146 10 false L51 5.521,2.396 5.792,2.542 0.271,0.146 10 false L51 5.51,0.698 5.781,0.844 0.271,0.146 10 false L50 5.563,7.094 6.958,7.281 1.396,0.188 10 false No. 2 Main Body ECU 5.896,2.396 6.927,2.542 1.031,0.146 10 false DC+ 5.896,3.688 6.927,3.833 1.031,0.146 10 false DC- 5.896,4.979 6.927,5.125 1.031,0.146 10 false DC+ 5.896,6.25 6.927,6.396 1.031,0.146 10 false DC- 5.896,0.698 6.323,0.844 0.427,0.146 10 false BDSU

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TAIL GATE PANEL OPEN)
a.

Select the Active Test, use the GTS to generate a control command, and check that the lower tail gate lock operates (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).

Body No. 4
Tester Display Test Part Control Range Diagnostic Note
Tail Gate Panel Open Lower tail gate lock ON / OFF The back door must be open.

OK:

Lower tail gate lock operates normally.




OK

2.READ VALUE USING GTS (HANDLE SWITCH OF TAIL GATE PANEL)

NG

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY
2.READ VALUE USING GTS (HANDLE SWITCH OF TAIL GATE PANEL)
a.

Check the Data List for proper functioning of the back door remote control (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).

Body No. 4
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Handle Switch of tail gate panel Back door remote control signal / ON or OFF ON: Back door remote control pulled
OFF: Back door remote control free
-

OK:

The display is as specified in the normal condition.




OK

NG

5.INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY
3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY
a.

for LH:

i.

Remove the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


ii.

Inspect the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).



b.

for RH:

i.

Remove the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


ii.

Inspect the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).



Result
Result Proceed to
OK A
NG (for LH) B
NG (for RH) C


A

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY - NO. 2 MAIN BODY ECU)

B

REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH

C

REPLACE LOWER TAIL GATE LOCK ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY - NO. 2 MAIN BODY ECU)
a.

for LH:

i.

Disconnect the h5 lower tail gate lock assembly LH connector.


ii.

Disconnect the L51 No. 2 main body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h5-5 (ACT+) - L51-3 (DC+) Always Below 1 Ω
h5-6 (ACT-) - L51-8 (DC-) Always Below 1 Ω
h5-5 (ACT+) - Body ground Always 10 kΩ or higher
h5-6 (ACT-) - Body ground Always 10 kΩ or higher




b.

for RH:

i.

Disconnect the h4 lower tail gate lock assembly RH connector.


ii.

Disconnect the L51 No. 2 main body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h4-5 (ACT+) - L51-2 (DC+) Always Below 1 Ω
h4-6 (ACT-) - L51-1 (DC-) Always Below 1 Ω
h4-5 (ACT+) - Body ground Always 10 kΩ or higher
h4-6 (ACT-) - Body ground Always 10 kΩ or higher





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY
a.

Remove the back door remote control assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


b.

Inspect the back door remote control assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR REMOTE CONTROL ASSEMBLY - NO. 2 MAIN BODY ECU AND BODY GROUND)

NG

REPLACE BACK DOOR REMOTE CONTROL ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BACK DOOR REMOTE CONTROL ASSEMBLY - NO. 2 MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the h3 back door remote control assembly connector.


b.

Disconnect the L50 No. 2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h3-2 - L50-19 (BDSU) Always Below 1 Ω
h3-1 - Body ground Always Below 1 Ω
h3-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR