Home › Vehicle Exterior › DOOR / HATCH › TAIL GATE CLOSER SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255760 TAIL GATE CLOSER SYSTEM C

DOOR / HATCH  TAIL GATE CLOSER SYSTEM  B225A  Tail Gate Panel Position Switch RH  


DESCRIPTION

The No. 2 main body ECU receives the close position switch signal from the lower tail gate lock assembly RH and detects the open/closed status of the lower tail gate. DTC B225A is stored when the No. 2 main body ECU receives a close position switch malfunction signal from the lower tail gate lock assembly RH.

DTC Code DTC Detection Condition Trouble Area
B225A A close position switch malfunction (open or short circuit) signal is received from the lower tail gate lock.
·

Lower tail gate lock assembly RH

·

Harness or connector

·

No. 2 main body ECU



WIRING DIAGRAM

B312260E01
5.408,1.703 5.980,1.853 0.572,0.150 10 L50 5.408,1.847 6.791,2.043 1.383,0.196 10 No. 2 Main Body ECU 1.764,1.197 1.943,1.347 0.179,0.150 10 h4 2.294,0.733 2.393,0.883 0.098,0.150 10 8 2.436,0.985 2.769,1.135 0.333,0.150 10 GND 3.367,0.733 3.545,0.883 0.179,0.150 10 7 3.003,0.991 3.323,1.141 0.320,0.150 10 HND 5.359,0.737 5.537,0.887 0.179,0.150 10 17 5.591,0.831 5.890,0.981 0.298,0.150 10 LMT 1.764,1.341 3.977,1.685 2.213,0.344 10 Lower Tail Gate Lock Assembly RH (Close Position Switch)

PROCEDURE

1.READ VALUE USING GTS (POSITION SWITCH RH)
a.

Check the Data List for proper functioning of the close position switch (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).

Body No. 4
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Position Switch RH Close position switch RH signal / ON or OFF ON: Lower tail gate closed
OFF: Lower tail gate open
-

OK:

The display is as specified in the normal condition.




OK

2.CHECK DTC OUTPUT

NG

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH
2.CHECK DTC OUTPUT
a.

Starting with the lower tail gate closed, open and close the lower tail gate 6 times.




d.

Starting with the lower tail gate closed, open and close the lower tail gate 6 times.


e.

Recheck for DTCs (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B225A is not output.




OK

NG

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH
a.

Remove the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


b.

Inspect the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY RH - NO. 2 MAIN BODY ECU AND BODY GROUND)

NG

REPLACE LOWER TAIL GATE LOCK ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY RH - NO. 2 MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the h4 lower tail gate lock assembly RH connector.


b.

Disconnect the L50 No. 2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h4-7 (HND) - L50-17 (LMT) Always Below 1 Ω
h4-8 (GND) - Body ground Always Below 1 Ω
h4-7 (HND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR