Home › Vehicle Exterior › DOOR / HATCH › TAIL GATE CLOSER SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255760 TAIL GATE CLOSER SYSTEM C

DOOR / HATCH  TAIL GATE CLOSER SYSTEM  B225C  Tail Gate Panel Position Switch LH  


DESCRIPTION

The No. 2 main body ECU receives the close position switch signal from the lower tail gate lock assembly LH and detects the open/closed status of the lower tail gate. DTC B225C is stored when the No. 2 main body ECU receives a close position switch malfunction signal from the lower tail gate lock assembly LH.

DTC Code DTC Detection Condition Trouble Area
B225C A close position switch malfunction (open or short circuit) signal from the lower tail gate lock LH is received.
·

Lower tail gate lock assembly LH

·

Harness or connector

·

No. 2 main body ECU



WIRING DIAGRAM

B312260E02
5.408,1.703 5.980,1.853 0.572,0.150 10 L51 5.408,1.847 6.791,2.043 1.383,0.196 10 No. 2 Main Body ECU 1.764,1.197 1.943,1.347 0.179,0.150 10 h5 2.294,0.733 2.393,0.883 0.098,0.150 10 8 2.436,0.985 2.769,1.135 0.333,0.150 10 GND 3.367,0.733 3.545,0.883 0.179,0.150 10 7 3.003,0.991 3.323,1.141 0.320,0.150 10 HND 5.359,0.737 5.537,0.887 0.179,0.150 10 10 5.591,0.831 5.890,0.981 0.298,0.150 10 LMT 1.764,1.341 3.977,1.685 2.213,0.344 10 Lower Tail Gate Lock Assembly LH (Close Position Switch)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (POSITION SWITCH LH)
a.

Check the Data List for proper functioning of the close position switch (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).

Body No. 4
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Position Switch LH Close position switch LH signal / ON or OFF ON: Lower tail gate closed
OFF: Lower tail gate open
-

OK:

The display is as specified in the normal condition.




OK

2.CHECK DTC OUTPUT

NG

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH
2.CHECK DTC OUTPUT
a.

Starting with the lower tail gate closed, open and close the lower tail gate 6 times.




d.

Starting with the lower tail gate closed, open and close the lower tail gate 6 times.


e.

Recheck for DTCs (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B225C is not output.




OK

NG

3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH
a.

Remove the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR(for Double Swing Out Type)>DISASSEMBLY).


b.

Inspect the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY LH - NO. 2 MAIN BODY ECU AND BODY GROUND)

NG

REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY LH - NO. 2 MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the h5 lower tail gate lock assembly LH connector.


b.

Disconnect the L51 No. 2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h5-7 (HND) - L51-10 (LMT) Always Below 1 Ω
h5-8 (GND) - Body ground Always Below 1 Ω
h5-7 (HND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR