Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door Sensor Circuit  


DESCRIPTION

When the power back door unit assembly (power back door ECU) receives a jam signal from the power back door sensor while the power back door closer is operating, the power back door unit assembly (power back door ECU) reverses the back door operation and opens the door.

WIRING DIAGRAM

B312259E04
5.125,3.802 5.677,3.948 0.552,0.146 10 false L52 5.531,3.229 5.708,3.375 0.177,0.146 10 false 14 2.917,1.99 3.25,2.135 0.333,0.146 10 false OSR 1.604,1.99 2.021,2.135 0.417,0.146 10 false OSRE 3.333,1.771 3.885,1.917 0.552,0.146 10 false 1 1.438,1.771 1.542,1.917 0.104,0.146 10 false 2 3.167,0.604 3.563,0.75 0.396,0.146 10 false OSLE 4.51,0.594 4.813,0.74 0.302,0.146 10 false OSL 2.99,0.365 3.094,0.51 0.104,0.146 10 false 2 4.865,0.365 4.969,0.51 0.104,0.146 10 false 1 5.531,1.781 5.708,1.927 0.177,0.146 10 false 13 5.531,0.375 5.708,0.521 0.177,0.146 10 false 15 5.823,3.344 6.375,3.49 0.552,0.146 10 false OSE 5.823,1.865 6.375,2.01 0.552,0.146 10 false OSR 5.823,0.469 6.375,0.615 0.552,0.146 10 false OSL 5.125,3.948 7.156,4.292 2.031,0.344 10 false Power Back Door Unit Assembly (Power back Door ECU) 1.219,2.469 1.771,2.615 0.552,0.146 10 false S23 1.219,2.625 3.688,2.969 2.469,0.344 10 false Power Back Door Sensor Assembly RH 2.771,1.063 3.323,1.208 0.552,0.146 10 false S24 2.771,1.208 5.24,1.552 2.469,0.344 10 false Power Back Door Sensor Assembly LH

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (PBD POWER BACK DOOR SENSOR)
a.

Check the Data List for proper functioning of the power back door sensor (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST).

Back Door
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PBD power back door sensor (Left) Power back door sensor LH signal / ON, OFF or Open ON: Power back door sensor LH pressed
OFF: Power back door sensor LH not pressed
Open: Power back door sensor LH circuit open
-
PBD power back door sensor (Right) Power back door sensor RH signal / ON, OFF or Open ON: Power back door sensor RH pressed
OFF: Power back door sensor RH not pressed
Open: Power back door sensor RH circuit open
-

OK:

The display is as specified in the normal condition.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT POWER BACK DOOR SENSOR ASSEMBLY
2.INSPECT POWER BACK DOOR SENSOR ASSEMBLY
a.

Remove the power back door sensor assembly (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL).


b.

Inspect the power back door sensor assembly (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION).

Result
Result Proceed to
OK A
NG (for LH) B
NG (for RH) C



A

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)

B

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

C

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)
a.

for LH:

i.

Disconnect the S24 power back door sensor assembly LH connector.


ii.

Disconnect the L52 power back door unit assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S24-1 (OSL) - L52-15 (OSL) Always Below 1 Ω
S24-2 (OSLE) - L52-14 (OSE) Always Below 1 Ω
S24-1 (OSL) - Body ground Always 10 kΩ or higher
S24-2 (OSLE) - Body ground Always 10 kΩ or higher




b.

for RH:

i.

Disconnect the S23 power back door sensor assembly RH connector.


ii.

Disconnect the L52 power back door unit assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S23-1 (OSR) - L52-13 (OSR) Always Below 1 Ω
S23-2 (OSRE) - L52-14 (OSE) Always Below 1 Ω
S23-1 (OSR) - Body ground Always 10 kΩ or higher
S23-2 (OSRE) - Body ground Always 10 kΩ or higher





OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR