Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2250  Back Door Closer Operation Malfunction  


DESCRIPTION

The power back door unit assembly (power back door ECU) inputs signals from the latch switch, closer position switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock assembly is determined.

DTC Code DTC Detection Condition Trouble Area
B2250 While back door closer is operating, malfunction is detected in position information from closer position switch within specified amount of time
·

Back door lock assembly

·

Harness or connector

·

Power back door unit assembly (power back door ECU)



WIRING DIAGRAM

B312260E05
5.053,1.731 5.625,1.881 0.572,0.150 10 L52 5.053,1.875 7.079,2.210 2.026,0.335 10 Power Back Door Unit Assembly (Power Back Door ECU) 2.016,1.225 2.370,1.375 0.353,0.150 10 S22 2.294,0.761 2.393,0.911 0.098,0.150 10 4 2.464,1.013 2.797,1.163 0.333,0.150 10 E 3.367,0.761 3.545,0.911 0.179,0.150 10 6 2.958,1.019 3.323,1.169 0.364,0.150 10 OPN 5.359,0.765 5.537,0.915 0.179,0.150 10 24 5.619,0.859 5.989,1.009 0.370,0.150 10 POS 2.016,1.37 3.682,1.714 1.666,0.344 10 Back Door Lock Assembly (Closer Position Switch)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CLOSER POSITION SW)
a.

Check the Data List for proper functioning of each switch (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST).

Back Door
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Closer Position SW Closer position switch signal / ON or OFF ON: Closer position switch is on
OFF: Closer position switch is off
-

OK:

The display is as specified in the normal condition.




OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY (CLOSER POSITION SW)
2.INSPECT BACK DOOR LOCK ASSEMBLY (CLOSER POSITION SW)
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)
a.

Disconnect the S22 back door lock assembly connector.


b.

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S22-6 (OPN) - L52-24 (POS) Always Below 1 Ω
S22-4 (E) - Body ground Always Below 1 Ω
S22-6 (OPN) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR