Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2251  Back Door Closer Switch Malfunction  


DESCRIPTION

The power back door unit assembly (power back door ECU) inputs signals from the latch switch, closer position switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock assembly is determined.

DTC Code DTC Detection Condition Trouble Area
B2251 While back door closer is operating, malfunction is detected in position information from each switch within specified amount of time
·

Back door lock assembly

·

Harness or connector

·

Power back door unit assembly (power back door ECU)



WIRING DIAGRAM

E336319E09
5.073,1.74 5.656,1.885 0.583,0.146 10 false L52 4.646,0.833 4.76,0.979 0.115,0.146 10 false 4 5.354,0.823 5.531,0.969 0.177,0.146 10 false 20 4.26,1.063 4.563,1.208 0.302,0.146 10 false CTY 2.094,1.115 3.813,1.26 1.719,0.146 10 false Back Door Courtesy Switch 1.948,1.635 2.531,1.781 0.583,0.146 10 false S33 1.948,1.823 3.594,2.271 1.646,0.448 10 false Back Door Lock Assembly 1.271,1.052 1.406,1.198 0.135,0.146 10 false E 1.083,0.844 1.198,0.99 0.115,0.146 10 false 1 5.635,0.948 6.219,1.094 0.583,0.146 10 false FUL 5.063,1.896 7.104,2.25 2.042,0.354 10 false Power Back Door Unit Assembly (Power Back Door ECU)

PROCEDURE

1.READ VALUE USING GTS (BACK DOOR LOCK)
a.

Check the Data List for proper functioning of each switch (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST).

Back Door
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Courtesy SW Back door courtesy switch signal / ON or OFF ON: Back door courtesy switch is on
OFF: Back door courtesy switch is off
-

OK:

The display is as specified in the normal condition.




OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY (BACK DOOR COURTESY SWITCH)
2.INSPECT BACK DOOR LOCK ASSEMBLY (BACK DOOR COURTESY SWITCH)
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] AND BODY GROUND)
a.

Disconnect the S33 back door lock assembly connector.


b.

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S33-4 (CTY) - L52-20 (FUL) Always Below 1 Ω
S33-1 (E) - Body ground Always Below 1 Ω
S33-4 (CTY) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR