Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper ECU controls the wiper motor.

WIRING DIAGRAM

E138460E03
0.567,4.185 2.069,4.591 1.502,0.407 10 A22 5.468,4.333 7.002,4.871 1.534,0.538 10 Windshield Wiper ECU 5.472,4.162 5.737,4.343 0.264,0.181 10 E83 5.199,0.94 5.355,1.121 0.156,0.181 10 1 5.169,1.621 5.324,1.802 0.156,0.181 10 2 5.183,2.394 5.339,2.576 0.156,0.181 10 7 5.169,3.064 5.324,3.245 0.156,0.181 10 8 5.401,1.06 5.642,1.241 0.241,0.181 10 +1 5.429,1.775 5.604,1.956 0.175,0.181 10 +2 5.401,2.517 5.737,2.699 0.336,0.181 10 +SM 5.401,3.204 5.696,3.385 0.295,0.181 10 WIG 2.063,0.735 2.331,0.916 0.267,0.181 10 1*1 2.063,0.915 2.331,1.096 0.267,0.181 10 5*2 2.077,1.477 2.331,1.658 0.254,0.181 10 4*1 2.077,2.234 2.354,2.415 0.276,0.181 10 3*1 2.063,3.064 2.219,3.245 0.156,0.181 10 2 2.077,3.551 2.331,3.732 0.254,0.181 10 5*1 1.786,1.046 1.962,1.227 0.175,0.181 10 +1 1.772,1.747 1.948,1.928 0.175,0.181 10 +2 1.758,2.489 1.949,2.671 0.191,0.181 10 +S 1.833,3.204 1.989,3.385 0.156,0.181 10 B 1.791,3.806 1.947,3.988 0.156,0.181 10 E 2.071,1.647 2.325,1.829 0.254,0.181 10 3*2 2.069,2.388 2.345,2.569 0.276,0.181 10 1*2 2.065,3.707 2.319,3.889 0.254,0.181 10 4*2 0.141,5.177 0.883,5.358 0.743,0.181 10 *1: for LHD 0.134,5.458 0.900,5.639 0.766,0.181 10 *2: for RHD 0.57,4.33 2.073,4.737 1.502,0.407 10 Front Wiper Motor

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT WIPER MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check the front wiper motor.

NOTICE:

When a Body No. 5 (windshield wiper ECU) related front wiper switch is on, Active Test items related to the front wiper switch are prohibited (double operation prohibition). Check that the front wiper switches are off before performing Active Test.


Body No. 5
Item Test Details Control Range Diagnostic Note
Wiper Mot (HI) Wiper motor HI operation ON / OFF -
Wiper Mot (LO) Wiper motor LO operation ON / OFF -

OK:

Front wiper motor operates.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FRONT WIPER MOTOR
2.INSPECT FRONT WIPER MOTOR
a.
E147181E07
2.083,2.115 2.521,2.135 true 1.948,2.531 2.51,2.542 false 1.49,2.438 0.781,1.823 true 0.917,1.406 1.417,2.042 true 2.573,2.052 3,2.229 0.427,0.177 10 false +1*1 2.542,2.448 3.01,2.625 0.469,0.177 10 false +2*1 0.469,1.708 0.854,1.885 0.385,0.177 10 false E*1 0.396,1.917 0.823,2.094 0.427,0.177 10 false +1*2 0.552,1.302 1.021,1.479 0.469,0.177 10 false +2*2 2.573,2.635 2.958,2.813 0.385,0.177 10 false E*2 0.24,2.583 1.052,2.76 0.813,0.177 10 false *1: for LHD 0.24,2.906 1.073,3.083 0.833,0.177 10 false *2: for RHD 0.313,0.146 2.781,0.49 2.469,0.344 10 false Component without harness connected: (Front Wiper Motor)

Remove the front wiper motor (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


b.

Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+1)
Battery negative (-) → Terminal 5 (E)
Motor operates at low speed
Battery positive (+) → Terminal 4 (+2)
Battery negative (-) → Terminal 5 (E)
Motor operates at high speed

for RHD
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (+1)
Battery negative (-) → Terminal 4 (E)
Motor operates at low speed
Battery positive (+) → Terminal 3 (+2)
Battery negative (-) → Terminal 4 (E)
Motor operates at high speed




OK

3.CHECK HARNESS AND CONNECTOR (FRONT WIPER MOTOR - WINDSHIELD WIPER ECU AND BODY GROUND)

NG

REPLACE FRONT WIPER MOTOR

3.CHECK HARNESS AND CONNECTOR (FRONT WIPER MOTOR - WINDSHIELD WIPER ECU AND BODY GROUND)
a.

Disconnect the A22 motor connector.

E349743E01
2.458,0.458 2.823,0.677 0.365,0.219 6.313,1.313 6.677,1.531 0.365,0.219 2.031,1.354 2.458,1.104 true 1.938,1.594 2.438,1.802 true 1.406,0.833 1.792,1.333 true 1.302,1.115 1.604,1.365 true 1.24,1.656 1.719,1.604 true 5.292,1.552 5.5,1.802 true 4.906,1.802 5,1.552 true 4.427,1.115 4.823,1.313 true 4.667,0.958 5,1.281 true 0.26,0.052 2.531,0.552 2.271,0.5 10 false Front view of wire harness connector: (to Front Wiper Motor) 4.219,0.042 6.49,0.542 2.271,0.5 10 false Front view of wire harness connector: (to Windshield Wiper ECU) 1.26,0.698 1.417,0.896 0.156,0.198 10 false B 0.938,1.063 1.323,1.406 0.385,0.344 10 false +1*1 +S*2 0.885,1.594 1.354,1.823 0.469,0.229 10 false +2*1 2.521,0.948 3.021,1.313 0.5,0.365 10 false +S*1 +2*2 2.521,1.719 2.875,1.927 0.354,0.208 10 false +1*2 2.5,0.49 2.885,0.719 0.385,0.229 10 false A22 4.458,0.792 4.688,1 0.229,0.208 10 false +2 4.229,1.01 4.469,1.198 0.24,0.188 10 false +1 6.365,1.333 6.865,1.563 0.5,0.229 10 false E83 4.74,1.844 5.156,2.083 0.417,0.24 10 false +SM 5.479,1.823 5.823,2.073 0.344,0.25 10 false WIG 0.115,2.208 1.042,2.406 0.927,0.198 10 false *1 : for LHD 0.146,2.458 1.229,2.698 1.083,0.24 10 false *2 : for RHD


b.

Disconnect the E83 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A22-2 (B) - E83-8 (WIG) Always Below 1 Ω
A22-1 (+1) - E83-1 (+1)
A22-4 (+2) - E83-2 (+2)
A22-3 (+S) - E83-7 (+SM)
A22-5 (E) - Body ground
A22-3 (+S) - Body ground Always 10 kΩ or higher
A22-2 (B) - Body ground
A22-4 (+2) - Body ground
A22-1 (+1) - Body ground

for RHD
Tester Connection Condition Specified Condition
A22-2 (B) - E83-8 (WIG) Always Below 1 Ω
A22-5 (+1) - E83-1 (+1)
A22-3 (+2) - E83-2 (+2)
A22-1 (+S) - E83-7 (+SM)
A22-4 (E) - Body ground
A22-1 (+S) - Body ground Always 10 kΩ or higher
A22-2 (B) - Body ground
A22-3 (+2) - Body ground
A22-5 (+1) - Body ground




OK

REPLACE WINDSHIELD WIPER ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR