The No. 2 multiplex network body ECU receives ambient air temperature information from the air conditioning amplifier assembly via CAN communication.
The washer nozzle heater assembly controls the No. 2 multiplex network body ECU and operates the washer nozzle heater assembly according to the ambient temperature.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Since the wiper and washer system has functions that use CAN communication, first confirm that there is no malfunction in the CAN communication system with the How to Proceed with Troubleshooting procedure (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM(w/ Rain Sensor)>HOW TO PROCEED WITH TROUBLESHOOTING).
Since the wiper and washer system has functions that use the air conditioning system, first confirm that there is no malfunction in the air conditioning system with the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING).
Using the intelligent tester, enter the following menus: Body / Body No. 4 / Active Test.
Select "Front Washer Nozzle Heater", and perform the Active Test.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-25 (WHTR) - Body ground | ·
Engine switch on (IG) ·
Active Test is not performed |
11 to 14 V |
| L50-25 (WHTR) - Body ground | ·
Engine switch on (IG) ·
Active Test is performed |
Below 1 V |
OK
NG
for LH:
Remove the washer nozzle heater assembly LH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>REMOVAL).
Inspect the washer nozzle heater assembly LH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>INSPECTION).
for RH:
Remove the washer nozzle heater assembly RH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>REMOVAL).
Inspect the washer nozzle heater assembly RH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>INSPECTION).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LH) | B |
| NG (for RH) | C |
A
B
C
Disconnect the z70 washer nozzle heater assembly LH connector.
Disconnect the z69 washer nozzle heater assembly RH connector.
Disconnect the 3C cowl side junction block RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z70-2 (L+) - 3C-2 | Always | Below 1 Ω |
| z69-2 (R+) - 3C-2 | Always | Below 1 Ω |
| z70-1 (L-) - Body ground | Always | Below 1 Ω |
| z69-1 (R-) - Body ground | Always | Below 1 Ω |
| z70-2 (L+) or 3C-2 - Body ground | Always | 10 kΩ or higher |
| z69-2 (R+) or 3C-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3B cowl side junction block RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3B-5 - Body ground | Engine switch on (IG) | 11 to 14 V |
| 3B-5 - Body ground | Engine switch off | Below 1 V |
OK
NG
Remove the cowl side junction block RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-5 - 3C-2 | Battery voltage applied between terminals 3C-16 and 3B-11 | Below 1 Ω |
| 3B-5 - 3C-2 | Battery voltage not applied between terminals 3C-16 and 3B-11 | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Sliding Roof System) | A |
| OK (w/o Sliding Roof System) | B |
| NG | C |
A
B
C
Disconnect the L50 No. 2 multiplex network body ECU connector.
Disconnect the 3B cowl side junction block RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-25 (WHTR) - 3B-11 | Always | Below 1 Ω |
| L50-25 (WHTR) or 3B-11 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3C cowl side junction block RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3C-16 - Body ground | Engine switch on (IG) | 11 to 14 V |
| 3C-16 - Body ground | Engine switch off | Below 1 V |
OK
NG
Remove the cowl side junction block RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-5 - 3C-2 | Battery voltage applied between terminals 3C-16 and 3B-11 | Below 1 Ω |
| 3B-5 - 3C-2 | Battery voltage not applied between terminals 3C-16 and 3B-11 | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Sliding Roof System) | A |
| OK (w/o Sliding Roof System) | B |
| NG | C |
A
B
C