Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2416  Height Control Sensor Malfunction  B241A  Rear Height Control Sensor  


DESCRIPTION

The DTC is stored when the headlight swivel ECU*1 or headlight leveling ECU*2 detects malfunctions in the rear height control sensor LH power source or rear height control sensor LH (w/o Active Height Control Suspension).

*1: w/ Dynamic Headlight Auto Leveling

*2: w/ Static Headlight Auto Leveling


The headlight swivel ECU receives signals indicating the height of the vehicle from the suspension control ECU (w/ Active Height Control Suspension).

DTC Code DTC Detection Condition Trouble Area
B2416 w/o Active Height Control Suspension:
·

Malfunction in the rear height control sensor LH.

·

Open or short in the rear height control sensor LH power source circuit.


·

Rear height control sensor sub-assembly LH (w/o Active Height Control Suspension)

·

Suspension control ECU (w/ Active Height Control Suspension)

·

Headlight swivel ECU assembly (w/ Dynamic Headlight Auto Leveling)

·

Headlight leveling ECU assembly (w/ Static Headlight Auto Leveling)

·

Harness or connector


w/ Active Height Control Suspension:
·

Malfunction in the suspension control ECU.

·

Open or short in the suspension control ECU circuit.


B241A
·

Malfunction in the rear height control sensor LH.

·

Open or short in the rear height control sensor LH circuit.



WIRING DIAGRAM

E225964E17
0.677,2.656 1.021,2.813 0.344,0.156 10 false N7 0.677,2.833 2.49,3.229 1.813,0.396 10 false Rear Height Control Sensor Sub-assembly LH 4.865,2.688 5.26,2.844 0.396,0.156 10 false E109 4.875,2.844 6.375,3.229 1.5,0.385 10 false Headlight Leveling ECU Assembly 1.625,0.833 1.948,0.99 0.323,0.156 10 false SHB 1.625,2.167 1.948,2.323 0.323,0.156 10 false SHG 1.531,1.49 1.948,1.646 0.417,0.156 10 false SHRL 5.073,0.854 5.396,1.01 0.323,0.156 10 false SBR 5.073,2.198 5.396,2.354 0.323,0.156 10 false SGR 5.073,1.531 5.49,1.688 0.417,0.156 10 false SHRL 2.063,0.74 2.188,0.896 0.125,0.156 10 false 1 4.771,0.74 4.958,0.896 0.188,0.156 10 false 12 4.771,1.417 4.958,1.573 0.188,0.156 10 false 19 4.771,2.073 4.958,2.229 0.188,0.156 10 false 21 2.073,1.406 2.198,1.563 0.125,0.156 10 false 2 2.073,2.073 2.198,2.229 0.125,0.156 10 false 3 0.125,0.042 2.74,0.344 2.615,0.302 12 false w/ Static Headlight Auto Leveling:

E225964E18
0.677,2.656 1.021,2.813 0.344,0.156 10 false N7 0.667,2.823 2.448,3.323 1.781,0.5 10 false Rear Height Control Sensor Sub-assembly LH 4.875,2.677 5.271,2.833 0.396,0.156 10 false E101 4.875,2.844 6.375,3.229 1.5,0.385 10 false Headlight Swivel ECU Assembly 1.615,0.865 1.938,1.021 0.323,0.156 10 false SHB 1.625,2.188 1.948,2.344 0.323,0.156 10 false SHG 1.531,1.531 1.948,1.688 0.417,0.156 10 false SHRL 5.073,0.844 5.396,1 0.323,0.156 10 false SBR 5.073,2.198 5.396,2.354 0.323,0.156 10 false SGR 5.073,1.51 5.49,1.667 0.417,0.156 10 false SHRL 2.073,0.729 2.198,0.885 0.125,0.156 10 false 1 4.771,0.729 4.958,0.885 0.188,0.156 10 false 18 4.771,1.396 4.958,1.552 0.188,0.156 10 false 19 4.771,2.073 4.958,2.229 0.188,0.156 10 false 21 2.073,1.396 2.198,1.552 0.125,0.156 10 false 2 2.073,2.073 2.198,2.229 0.125,0.156 10 false 3 0.083,0.063 5.948,0.333 5.865,0.271 12 false w/ Dynamic Headlight Auto Leveling, w/o Active Height Control Suspension

E247668E02
0.156,0.135 5.646,0.438 5.49,0.302 12 false w/ Dynamic Headlight Auto Leveling, w/ Active Height Control Suspension 2.469,0.885 2.844,1.156 0.375,0.271 10 false 23 4.594,0.979 4.99,1.229 0.396,0.25 10 false 18 4.594,1.365 4.948,1.583 0.354,0.219 10 false 19 4.604,1.75 4.896,1.979 0.292,0.229 10 false 17 4.604,2.146 4.927,2.396 0.323,0.25 10 false 21 1.958,1.063 2.469,1.323 0.51,0.26 10 false SHB5 4.854,1.031 5.354,1.292 0.5,0.26 10 false SBR 1.958,1.469 2.552,1.813 0.594,0.344 10 false SHR2 4.865,1.448 5.365,1.708 0.5,0.26 10 false SHRL 4.854,1.875 5.417,2.146 0.563,0.271 10 false SHFL 1.958,2.25 2.542,2.615 0.583,0.365 10 false SHG5 4.875,2.25 5.333,2.51 0.458,0.26 10 false SGR 2.469,1.292 2.792,1.563 0.323,0.271 10 false 28 2.469,1.698 2.844,1.948 0.375,0.25 10 false 22 2.469,2.083 2.854,2.385 0.385,0.302 10 false 11 1.958,1.865 2.615,2.115 0.656,0.25 10 false SHF2 0.938,2.823 2.719,3.073 1.781,0.25 10 false Suspension Control ECU 4.729,2.969 6.385,3.385 1.656,0.417 10 false Headlight Swivel ECU Assembly 2.417,1.073 2.74,1.365 0.323,0.292 10 false K35 2.406,1.875 2.771,2.156 0.365,0.281 10 false K35 2.406,2.26 2.708,2.51 0.302,0.25 10 false K35 2.406,1.479 2.74,1.75 0.333,0.271 10 false K36 4.698,2.771 5.135,3 0.438,0.229 10 false E101

CAUTION / NOTICE / HINT

NOTICE:

After replacing the headlight leveling ECU*1 or headlight swivel ECU*2 and rear height control sensor LH, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).

*1: w/ Static Headlight Auto Leveling

*2: w/ Dynamic Headlight Auto Leveling



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2416 or B241A output does not occur.




OK

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
w/ Static Headlight Auto Leveling A
w/ Dynamic Headlight Auto Leveling, w/o Active Height Control Suspension B
w/ Dynamic Headlight Auto Leveling, w/ Active Height Control Suspension C



A

3.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)

B

6.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)

C

9.CHECK FOR DTC (ACTIVE HEIGHT CONTROL SUSPENSION)
3.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor power supply value / 0 to 5 V 4.7 to 5.2 V -
Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.

OK:

Normal conditions listed above are displayed.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the E109 headlight leveling ECU connector.


b.

Disconnect the N7 rear height control sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E109-12 (SBR) - N7-1 (SHB) Always Below 1 Ω
E109-19 (SHRL) - N7-2 (SHRL) Always Below 1 Ω
E109-21 (SGR) - N7-3 (SHG) Always Below 1 Ω
E109-12 (SBR) - Body ground Always 10 kΩ or higher
E109-19 (SHRL) - Body ground Always 10 kΩ or higher
E109-21 (SGR) - Body ground Always 10 kΩ or higher




OK

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION).



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

6.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

AFS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Height control sensor power supply value / 0 to 6.25 V 4.7 to 5.2 V -
Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
7.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the E101 headlight swivel ECU connector.


b.

Disconnect the N7 rear height control sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-18 (SBR) - N7-1 (SHB) Always Below 1 Ω
E101-19 (SHRL) - N7-2 (SHRL) Always Below 1 Ω
E109-21 (SGR) - N7-3 (SHG) Always Below 1 Ω
E101-18 (SBR) - Body ground Always 10 kΩ or higher
E101-19 (SHRL) - Body ground Always 10 kΩ or higher
E109-21 (SGR) - Body ground Always 10 kΩ or higher




OK

8.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION).

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

9.CHECK FOR DTC (ACTIVE HEIGHT CONTROL SUSPENSION)
a.

Check for DTCs (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>DTC CHECK / CLEAR).

OK:

DTC "C1712 Front Height Control Sensor LH Circuit Malfunction" and "C1714 Rear Height Control Sensor LH Circuit Malfunction" output does not occur.




OK

10.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)

NG

10.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

AFS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Height control sensor power supply value / 0 to 6.25 V 4.7 to 5.2 V -
Fr Height Sens Signal Val Front height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.
Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - SUSPENSION CONTROL ECU)
11.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - SUSPENSION CONTROL ECU)
a.

Disconnect the E101 headlight swivel ECU connector.


b.

Disconnect the K35 and K36 suspension control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-18 (SBR) - K35-23 (SHB5) Always Below 1 Ω
E101-19 (SHRL) - K36-28 (SHR2) Always Below 1 Ω
E101-17 (SHFL) - K35-22 (SHF2) Always Below 1 Ω
E101-21 (SGR) - K35-11 (SHG5) Always Below 1 Ω
E101-18 (SBR) - Body ground Always 10 kΩ or higher
E101-19 (SHRL) - Body ground Always 10 kΩ or higher
E101-17 (SHFL) - Body ground Always 10 kΩ or higher
E101-21 (SGR) - Body ground Always 10 kΩ or higher




OK

12.CHECK SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK SUSPENSION CONTROL ECU
a.
U166080E01
0.148,0.126 0.435,0.347 0.287,0.222 10 *a 0.841,1.26 1.108,1.423 0.267,0.163 10 K36 1.607,1.26 1.874,1.423 0.267,0.163 10 K35 0.127,2.859 0.552,3.003 0.425,0.144 10 SHR2 0.837,2.142 0.374,2.831 false 2.209,2.684 2.645,2.834 0.436,0.150 10 SHG5 1.079,2.655 1.502,2.818 0.423,0.162 10 SHB5 1.75,2.983 2.140,3.132 0.391,0.150 10 SHF2 1.795,2.065 2.415,2.646 false 1.581,2.137 1.333,2.638 false 1.636,2.137 1.977,2.939 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K35-23 (SHB5) - K35-11 (SHG5) Ignition switch ON 4.5 to 5.5 V
K35-22 (SHF2) - K35-11 (SHG5) Ignition switch ON Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
K36-28 (SHR2) - K35-11 (SHG5) Ignition switch ON Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)


Text in Illustration
*a Component with harness connected
(Suspension Control ECU)

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPLACE SUSPENSION CONTROL ECU