Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2416  Height Control Sensor Malfunction  B241A  Rear Height Control Sensor  


DESCRIPTION

The DTC is stored when the headlight swivel ECU*1 or headlight leveling ECU*2 detects malfunctions in the rear height control sensor LH power source.

*1: w/ Dynamic Headlight Auto Leveling

*2: w/ Static Headlight Auto Leveling


DTC Code DTC Detection Condition Trouble Area
B2416
·

Malfunction in the rear height control sensor LH.

·

Open or short in the rear height control sensor LH power source circuit.


·

Rear height control sensor sub-assembly LH

·

Headlight swivel ECU assembly (w/ Dynamic Headlight Auto Leveling)

·

Headlight leveling ECU assembly (w/ Static Headlight Auto Leveling)

·

Harness or connector


B241A
·

Malfunction in the rear height control sensor LH.

·

Open or short in the rear height control sensor LH circuit.


·

Rear height control sensor sub-assembly LH

·

Headlight swivel ECU assembly (w/ Dynamic Headlight Auto Leveling)

·

Headlight leveling ECU assembly (w/ Static Headlight Auto Leveling)

·

Harness or connector



WIRING DIAGRAM

E225964E17
0.677,2.656 1.021,2.813 0.344,0.156 10 false N7 0.677,2.833 2.49,3.229 1.813,0.396 10 false Rear Height Control Sensor Sub-assembly LH 4.865,2.688 5.26,2.844 0.396,0.156 10 false E109 4.875,2.844 6.375,3.229 1.5,0.385 10 false Headlight Leveling ECU Assembly 1.625,0.833 1.948,0.99 0.323,0.156 10 false SHB 1.625,2.167 1.948,2.323 0.323,0.156 10 false SHG 1.531,1.49 1.948,1.646 0.417,0.156 10 false SHRL 5.073,0.854 5.396,1.01 0.323,0.156 10 false SBR 5.073,2.198 5.396,2.354 0.323,0.156 10 false SGR 5.073,1.531 5.49,1.688 0.417,0.156 10 false SHRL 2.063,0.74 2.188,0.896 0.125,0.156 10 false 1 4.771,0.74 4.958,0.896 0.188,0.156 10 false 12 4.771,1.417 4.958,1.573 0.188,0.156 10 false 19 4.771,2.073 4.958,2.229 0.188,0.156 10 false 21 2.073,1.406 2.198,1.563 0.125,0.156 10 false 2 2.073,2.073 2.198,2.229 0.125,0.156 10 false 3 0.125,0.042 2.74,0.344 2.615,0.302 12 false w/ Static Headlight Auto Leveling:

E225964E19
0.688,2.698 1.594,2.875 0.906,0.177 10 false N7 0.677,2.865 2.427,3.26 1.75,0.396 10 false Rear Height Control Sensor Sub-assembly LH 4.875,2.708 5.271,2.865 0.396,0.156 10 false E101 4.885,2.875 6.385,3.26 1.5,0.385 10 false Headlight Swivel ECU Assembly 1.625,0.792 1.948,0.948 0.323,0.156 10 false SHB 1.625,2.125 1.948,2.281 0.323,0.156 10 false SHG 1.531,1.438 1.948,1.594 0.417,0.156 10 false SHRL 5.073,0.792 5.396,0.948 0.323,0.156 10 false SBR 5.073,2.125 5.396,2.281 0.323,0.156 10 false SGR 5.073,1.438 5.49,1.594 0.417,0.156 10 false SHRL 2.073,0.667 2.198,0.823 0.125,0.156 10 false 1 4.771,0.667 4.958,0.823 0.188,0.156 10 false 18 4.771,1.354 4.958,1.51 0.188,0.156 10 false 19 4.771,2.021 4.958,2.177 0.188,0.156 10 false 21 2.073,1.344 2.198,1.5 0.125,0.156 10 false 2 2.073,2.021 2.198,2.177 0.125,0.156 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the headlight leveling ECU*1 or headlight swivel ECU*2 and rear height control sensor LH, initialization of the ECU is necessary (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).

*1: w/ Static Headlight Auto Leveling

*2: w/ Dynamic Headlight Auto Leveling



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2416 or B241A output does not occur.




OK

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
w/ Static Headlight Auto Leveling A
w/ Dynamic Headlight Auto Leveling B



A

3.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)

B

6.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)
3.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)
a.

Using the GTS, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor power supply value / 0 to 5 V 4.7 to 5.2 V -
Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.

OK:

Normal conditions listed above are displayed.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the E109 headlight leveling ECU connector.


b.

Disconnect the N7 rear height control sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E109-12 (SBR) - N7-1 (SHB) Always Below 1 Ω
E109-19 (SHRL) - N7-2 (SHRL) Always Below 1 Ω
E109-21 (SGR) - N7-3 (SHG) Always Below 1 Ω
E109-12 (SBR) - Body ground Always 10 kΩ or higher
E109-19 (SHRL) - Body ground Always 10 kΩ or higher
E109-21 (SGR) - Body ground Always 10 kΩ or higher




OK

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION).



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

6.READ VALUE USING GTS (REAR HEIGHT CONTROL SENSOR)
a.

Using the GTS, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

AFS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Height control sensor power supply value / 0 to 6.25 V 4.7 to 5.2 V -
Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value changes according to the vehicle height.

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
7.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the E101 headlight swivel ECU connector.


b.

Disconnect the N7 rear height control sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-18 (SBR) - N7-1 (SHB) Always Below 1 Ω
E101-19 (SHRL) - N7-2 (SHRL) Always Below 1 Ω
E109-21 (SGR) - N7-3 (SHG) Always Below 1 Ω
E101-18 (SBR) - Body ground Always 10 kΩ or higher
E101-19 (SHRL) - Body ground Always 10 kΩ or higher
E109-21 (SGR) - Body ground Always 10 kΩ or higher




OK

8.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor LH (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION).

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH