Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

The illumination of the low beam headlights is controlled by the main body ECU (multiplex network body ECU). When the headlights are turned on, the main body ECU (multiplex network body ECU) receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.

DTC Code DTC Detection Condition Trouble Area
B2430 LED headlight LH circuit malfunction
·

Headlight assembly LH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


B2431 LED headlight RH circuit malfunction
·

Headlight assembly RH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



HINT:

DTC B2430 and B2431 are not output if 20 seconds have not elapsed since the ignition switch was turned on.


WIRING DIAGRAM

E336602E03
2.635,0.354 4.469,0.552 1.833,0.198 10 false from Battery 0.708,0.521 2.573,0.708 1.865,0.188 10 false H-LP MAIN NO.1 or H-LP RH 1.271,1.229 1.51,1.406 0.24,0.177 10 false 1 1.281,1.625 1.521,1.802 0.24,0.177 10 false 3 2.083,1.219 2.323,1.396 0.24,0.177 10 false 2 1.146,2.073 2.469,2.25 1.323,0.177 10 false H-LP LO or H-LP LH 2.083,1.625 2.323,1.802 0.24,0.177 10 false 5 3.531,1.198 4.323,1.396 0.792,0.198 10 false 30 3.781,1.885 4.573,2.083 0.792,0.198 10 false 2H 5.5,1.344 6.292,1.542 0.792,0.198 10 false A 3.792,2.031 5.615,2.292 1.823,0.26 10 false Cowl Side Junction Block LH 5.479,1.104 6.271,1.302 0.792,0.198 10 false 15 5.833,1.354 6.625,1.552 0.792,0.198 10 false HRLY 5.375,4.333 5.823,4.604 0.448,0.271 10 false E118 5.458,4.125 6.292,4.51 0.833,0.385 10 false 16 5.823,4.344 6.656,4.729 0.833,0.385 10 false LLEW 5.396,6.76 5.813,7.021 0.417,0.26 10 false E118 5.49,6.552 5.667,6.75 0.177,0.198 10 false 3 5.833,6.792 6.667,7.177 0.833,0.385 10 false RLEW 5.365,7.76 7.052,8.115 1.688,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 3.24,6.385 4.469,6.719 1.229,0.333 10 false H-LP RH-LO 2.552,6.208 2.844,6.396 0.292,0.188 10 false LO 2.635,6.74 2.813,6.927 0.177,0.188 10 false S 0.875,7.302 1.25,7.469 0.375,0.167 10 false A68 0.875,7.469 2.396,7.656 1.521,0.188 10 false Headlight Assembly RH 0.823,4.844 1.198,5.01 0.375,0.167 10 false A65 0.823,5.01 2.292,5.198 1.469,0.188 10 false Headlight Assembly LH 2.563,3.781 2.854,3.969 0.292,0.188 10 false LO 2.615,4.333 2.792,4.521 0.177,0.188 10 false S 3.188,3.969 4.417,4.302 1.229,0.333 10 false H-LP LH-LO 2.865,3.667 3.156,3.854 0.292,0.188 10 false 1 2.885,4.219 3.177,4.406 0.292,0.188 10 false 7 2.885,6.635 3.177,6.823 0.292,0.188 10 false 7 2.885,6.104 3.177,6.292 0.292,0.188 10 false 1 0.76,6.5 0.938,6.688 0.177,0.188 10 false E 0.781,4.063 0.958,4.25 0.177,0.188 10 false E 0.573,3.938 0.75,4.125 0.177,0.188 10 false 2 0.573,6.375 0.75,6.563 0.177,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>PRECAUTION).



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 output does not occur.




OK

NG

3.INSPECT HEADLIGHT RELAY (H-LP LO OR H-LP LH)
3.INSPECT HEADLIGHT RELAY (H-LP LO OR H-LP LH)
a.
E234221E03
2.469,1.646 2.469,1.438 false 3.042,1.083 2.813,1.083 false 2.063,1.083 1.833,1.083 false 2.573,0.51 2.458,0.719 false 1.281,0.708 1.438,0.906 0.156,0.198 10 false 3 0.469,1.281 0.625,1.479 0.156,0.198 10 false 2 1.271,1.281 1.427,1.479 0.156,0.198 10 false 1 0.479,0.708 0.635,0.906 0.156,0.198 10 false 5 1.708,1 1.865,1.198 0.156,0.198 10 false 3 3.104,0.99 3.26,1.188 0.156,0.198 10 false 5 2.594,0.365 2.75,0.563 0.156,0.198 10 false 1 2.427,1.677 2.583,1.875 0.156,0.198 10 false 2

Remove the headlight relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP LO OR H-LP LH)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - BATTERY)
a.
E330447E01
0.093,0.06 0.279,0.219 0.186,0.158 10 *a

Remove the headlight relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 1 - Body ground Always 11 to 14 V
Headlight relay terminal 3 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Headlight Relay)



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - COWL SIDE JUNCTION BLOCK LH)
a.

Remove the headlight relay from the engine room relay block.


b.

Disconnect the 2H cowl side junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - 2H-30 Always Below 1 Ω
2H-30 - Body ground Always 10 kΩ or higher




OK

6.INSPECT COWL SIDE JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT COWL SIDE JUNCTION BLOCK LH
a.
U156815E03
1.583,2.615 1.719,2.927 1.719,2.927 1.969,2.927 false 2.01,2.844 2.604,3 0.594,0.156 10 false HRLY 0.313,1 0.646,1.188 0.333,0.188 10 false 2H 1.583,2.083 1.865,2.24 0.281,0.156 10 false A

for LHD:

i.

Remove the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).


ii.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).



b.

for RHD:

i.

Remove the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).


ii.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-15 (HRLY) - 2H-30 Always Below 1 Ω


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - HEADLIGHT)

B

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO OR H-LP LH] - HEADLIGHT)
a.

Remove the headlight relay from the engine room relay block.


b.

Disconnect the A65*1 or A68*2 headlight connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A65-1 (LO) Always Below 1 Ω
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - A68-1 (LO) Always Below 1 Ω
Headlight relay terminal 5 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the A65*1 or A68*2 headlight unit connector.

*1: for LH

*2: for RH



b.

Disconnect the E118 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
A65-7 (S) - E118-16 (LLEW) Always Below 1 Ω
A65-2 (E) - Body ground Always Below 1 Ω
A65-7 (S) - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
A68-7 (S) - E118-3 (RLEW) Always Below 1 ΩS
A68-2 (E) - Body ground Always Below 1 Ω
A68-7 (S) - Body ground Always 10 kΩ or higher




OK

9.CHECK HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT ASSEMBLY
a.

for LED Headlight:

i.

Temporarily replace the headlight with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).



b.

for Halogen Headlight and LED Headlight:

i.

Temporarily replace the headlight with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight and LED Headlight)>REMOVAL).



c.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 output does not occur.



Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

END (HEADLIGHT WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)